Specifications; Jig Saw Safety Warnings - Makita 4351T Betriebsanleitung

ENGLISH
(Original instructions)
1 Cutting action changing lever
2 Switch lever
3 Speed adjusting dial
4 Tool opener
5 Blade clamp
6 Jig saw blade
7 Protrusions
8 Base
9 Hex wrench
10 Cutting line

SPECIFICATIONS

Model
Length of stroke............................................................. 26 mm
Max. cutting capacities
Wood .......................................................................... 135 mm
Steel ........................................................................... 10 mm
Aluminum ................................................................... 20 mm
Strokes per minute (min
Overall length ................................................................ 271 mm
Net weight ..................................................................... 2.5 kg
Safety class ...................................................................
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
Intended use
The tool is intended for the sawing of wood, plastic and
metal materials. As a result of the extensive accessory
and saw blade program, the tool can be used for many
purposes and is very well suited for curved or circular
cuts.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated and can, therefore, also be used from
sockets without earth wire.
General Power Tool Safety Warnings
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and instructions for future refer-
ence.
6
Explanation of general view
11 Bolt
12 Graduation
13 Bevel slot
14 Gear housing
15 V-notch
16 Starting hole
17 Dust nozzle
18 Hose for vacuum cleaner
19 Rip fence
20 Fence guide
–1
) ........................................... 2,800
4351T
/II

JIG SAW SAFETY WARNINGS

1. Hold power tool by insulated gripping surfaces
when performing an operation where the cutting
tool may contact hidden wiring or its own cord.
ENE019-1
Cutting accessory contacting a "live" wire may make
exposed metal parts of the power tool "live" and
could give the operator an electric shock.
2. Use clamps or another practical way to secure
and support the workpiece to a stable platform.
Holding the work by hand or against your body
leaves it unstable and may lead to loss of control.
ENF002-2 3. Always use safety glasses or goggles. Ordinary
eye or sun glasses are NOT safety glasses.
4. Avoid cutting nails. Inspect workpiece for any
nails and remove them before operation.
5. Do not cut oversize workpiece.
6. Check for the proper clearance beyond the work-
piece before cutting so that the blade will not
strike the floor, workbench, etc.
GEA010-1
7. Hold the tool firmly.
8. Make sure the blade is not contacting the work-
piece before the switch is turned on.
9. Keep hands away from moving parts.
10. Do not leave the tool running. Operate the tool
only when hand-held.
11. Always switch off and wait for the blade to come
to a complete stop before removing the blade
from the workpiece.
12. Do not touch the blade or the workpiece immedi-
ately after operation; they may be extremely hot
and could burn your skin.
13. Do not operate the tool at no-load unnecessarily.
14. Some material contains chemicals which may be
toxic. Take caution to prevent dust inhalation
and skin contact. Follow material supplier safety
data.
21 Threaded knob
22 Circular guide pin
23 Rule bar
24 Screw
25 Guide rail adapter
26 Guide rail
27 Cover plate
28 Anti-splintering device
4351CT 4351FCT
26 mm 26 mm
135 mm 135 mm
10 mm 10 mm
20 mm 20 mm
800 – 2,800 800 – 2,800
271 mm 271 mm
2.5 kg 2.5 kg
/II /II
GEB016-3