English - IKEA GALANT Bedienungsanleitung

ENGLISH

Advice and instructions for GALANT.
— Manufacturer: ROL Ergo AB, Lidtorpsvä- — The table is now ready for use. The mo-
gen 12 S-556 28
— Jönköping, Sweden.
— Tripod type: RE-046/047
— Protection class: IP20 Usage of the table
— Weight: 33 kg — The table can only be used as a working
— Sound level: lower than 70 dB(A)
— Height setting interval: 68-118 cm (with
spacing sleeves 73-123 cm)
— Maximum load: 80 kg
— Temperature interval at usage: +5 up to
+40 degrees C
— Temperature interval at storage: -10 up
to +50 degrees C
Humidity: 20% up to 80% at +30 degrees
C.
— The table must not be overloaded -
Every person who is responsible for this
table at installation or employment of the
table in daily use or in service and repair
work should carefully read these instruc-
tions. Keep these instructions in the plastic
pocket enclosed with your sit/ stand table.
— Follow these instructions when adjusting
Installation instructions:
— The table is assembled according to
separate assembly instructions. — Insert the safety key in the socket on
— For correct combination of table top and
tripod size - see assembly instructions. — Make sure no objects are in the way of
— Connect the plugs from the motors in
the two table legs to the sockets on the — In order to run the table up/down, press
command box. In a similar way, connect
the plug from the hand control. Place
the electrical cables so that they do not
— When the table is left unattended, the
get damaged. See assembly instruc-
tions. Cables from the motors and the
hand control should be attached to the
frame with the enclosed cable tape. Safety regulations
— Connect the electrical cable to a wall — When the table is run up/down there
socket. NB! The electrical cable must
have full mobility.
— Insert the safety key in the socket on — It is easy to get squeezed between the
4
the hand control.
tors stop automatically when the table
reaches its lowest and highest position
respectively.
table with the possibility to continuously
adjust working height between sitting
and standing position. The table can
only be used indoors and in dry prem-
ises (office environment or similar).
Lowest height from floor to the upper
edge of the table top is approx. 68 cm
and the highest height is 118 cm. If a
spacing sleeve is mounted on the legs
these measurements are increased by
5 cm.
maximum load is 80 kg. The motors
may be run continuously for maximum
2 minutes. Afterward, the motors must
stand by for approx. 18 minutes before
they can be used again.
table height:
the hand control.
the table adjusting height freely.
the manoeuvre button with an arrow
pointing up and down respectively.
safety key must be removed from the
hand control and placed out of chil-
dren's reach.
may be a risk of getting squeezed. Con-
sider the following:
moving table top and fixed objects in
the surrounding area. Necessary safety afterwards. Press, within 10 seconds, once
distance depends on what risk of get- again the same button and hold it for at
ting squeezed is considered greatest - least 5 seconds. The table is now ready for
from finger min. 3 cm to e.g. body/head use. If the table still does not work, please
of a child min. 40 cm. contact your nearest IKEA store.
— When the table is run up/down the user
shall keep watch so that nobody is
injured or no object is damaged. The
table top must not bump into a fixed
object so that the table is overturned.
Always remove any office chair before
the table is run up/down.
— When the table is left unattended, the
safety key must be removed from the
hand control and placed out of reach of
children.
— The table tripod must not be altered or
reconstructed in any way. In service
and repair work of the table, the electri-
cal cable should always be disconnected
from the wall socket.
— Alterations to the control box are abso-
lutely forbidden!
— The table must not be used as a hoisting
device for persons.
Maintenance and repair instructions
After approx. 1 week of use, check that the
screws mounted after delivery are properly
tightened. If the table can not be lowered
or raised, the connections to the command
box and wall socket should be checked as
well as if the safety key is properly inserted
in the hand control. On the hand control
there is a green control light. If this shines
when any of the two manoeuvre buttons
are pressed, there is power leading to the
command box, and conversely, if the green
light does not shine there is no power lead-
ing to the command box. If any part of the
electrical system is replaced, the system
must be reset as follows:
Run the table to its lowest position by
pressing the manoeuvre button with an
arrow pointing down. Release the button
5