Operation; Disposal And Recycling - EINHELL TC-CG 3,6/1 Li Originalbetriebsanleitung

Important!
To avoid causing damage to the inside of the
equipment, do not pull the glue stick out of the
equipment again after it has has melted.

6. Operation

6.1 Operation (Fig. 2)
•
Check that a glue stick is fitted (see point 5.2)
•
Press the On/Off switch (1) for approx. 3 se-
conds.
•
The LED (2b) will light up red to indicate that
the equipment is heating up
•
This takes approx. 30 seconds, after which
the LED (2a) will light up green.
•
The equipment is now ready for operation.
•
To switch the equipment off again, press the
ON/OFF briefly just the once
Warning!
Never set the equipment down once you have
started using it.
If or when your gluing work is interrupted or fi ni-
shed, always be sure to stand the equipment on
its support bar as shown in Fig. 4.
Switch the equipment off and allow it to cool down
completely before you pack it away.
6.2 Working with the cordless hot glue gun
•
You can now apply the glue by pressing the
trigger lever (4) after the heating up time
•
Press both surfaces together immediately
and apply pressure to them
•
It takes about 30 seconds for the glue to set.
•
Use the support bar (7) (Fig. 4) to set down
the cordless hot glue gun safely.
The equipment switches off automatically after
approx. 5 minutes of non-use.
Important!
Glue stains on textiles cannot be removed.
6.3 LED indicator (Fig. 2/Item 2)
The indicator (2) displays the charging status du-
ring charging (see point 5.1), the heating time and
when the equipment is ready for operation (see
point 6.1). If the red LED (2b) fl ashes during ope-
ration, the battery is empty. Recharge the battery.
Anl_TC_CG_3_6_1_Li_SPK9.indb 16 Anl_TC_CG_3_6_1_Li_SPK9.indb 16
GB
7. Cleaning, maintenance and
ordering of spare parts
Warning!
Allow the equipment to cool down before you start
to clean it.
7.1 Cleaning
•
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it with compressed air at low
pressure.
•
We recommend that you clean the device
immediately each time you have finished
using it.
•
Clean the equipment regularly with a moist
cloth and some soft soap. Do not use
cleaning agents or solvents; these could at-
tack the plastic parts of the equipment. Ensu-
re that no water can seep into the device. The
ingress of water into an electric tool increases
the risk of an electric shock.
7.2 Maintenance
There are no parts inside the equipment which
require additional maintenance.
7.3 Ordering replacement parts:
Please quote the following data when ordering
replacement parts:
•
Type of machine
•
Article number of the machine
•
Identification number of the machine
•
Replacement part number of the part required
For our latest prices and information please go to
www.isc-gmbh.info

8. Disposal and recycling

The equipment is supplied in packaging to pre-
vent it from being damaged in transit. The raw
materials in this packaging can be reused or
recycled. The equipment and its accessories are
made of various types of material, such as metal
and plastic. Never place defective equipment in
your household refuse. The equipment should
be taken to a suitable collection center for proper
disposal. If you do not know the whereabouts of
such a collection point, you should ask in your
local council offi ces.
- 16 -
9.
Sto
and
idea
°C.
11.10.2018 07:25:20 11.10.2018 07:25:20