Installation - Femi 784 XL Gebrauchsanleitung Und Wartung

1.6 SAFETY PROCEDURS FOR FURTHER RISK
- Always keep processing residues away from the cutting
area.
- Always use the clamp. The parts to be cut must always
be held fi rmly in the clamp.
- Always keep hands away from the working areas while
the machine is moving: before loading or unloading the
part, release the run button on the hand grip.
- Do not force the machine unnecessarily : excessive
cutting pressure could cause rapid wear to the blade and
negatively infl uence the per formance of the machine in
terms of fi nishes and cutting precision.
1.7 INFORMATION REGARDING NOISE AND
VIBRATIONS
Noise
Noise level at the operator's work
position (without load) ................................... Leq 81.5 dB (A)
Noise level at the operator's work position (with load)
Cutting of 80 mm dia. barstock in 9SMnPb28 steel at speed of
80 m/min .......................................................... Leq 82.4 dB(A)
Cutting of 60x60 steel profi le with 3 mm wall thickness at speed
of 80 m/min. ..................................................... Leq 85.6 dB(A)
Test conditions
Sound power (without load) ..........................Lwa 92.6 dB (A)
Sound power (with load) ...........................................................
Cutting of 80 mm dia. barstock in 9SMnPb28 steel at speed of
80 m/min ...................................................... Lwa 71.4 dB (A)
Cutting of 60x60 steel profi le with 3 mm wall thickness at speed
of 80 m/min. ...................................................Lwa 74.6 dB (A)
The measurements were carried out in accordance with
standard UNI EN ISO 3746.
Vibration
Mean frequency-weighted hand - arm acceleration vibration
exposure does not exceed 2.5 m/s².
The measurements were carried out in accordance with
standards UNI EN ISO 5349-1 and 5349-2.
The emission levels indicated are not necessarily safety
levels. Although there is a relationship between the emissions
and exposure levels, the values shown cannot be used for
establishing the need for further precautions. There are other
factors which infl uence the exposure levels of operators, such
as the features of the work place, presence of other sources
of noise, number of machines running, etc.
The exposure levels may also vary between countries.
This information is necessary for the user for better evaluation
of the risks and hazards deriving from noise.
NOTE: Personal hearing protection should be used,
such as headphones or earplugs.
1.8 INFORMATION ABOUT THE
ELECTROMAGNETIC COMPATIBILITY
The European regulations on safety and, in particular,
the Direc tive 2004/108/CE contemplate that all the
equipment be equipped with shield ing devices against radio
interferences both from and towards the outside.
This machine is equipped with fi lters both on the motor and
on the power supply through which the machine is safe and
in compliance with above regulations.
Tests were carried out according to EN 55014-1, EN
55014-2 regulations.
8
1.9 DESCRIPTION OF THE MACHINE (Fig.1)
The belt sawing machine consists of two basic parts: the
machine body 5 complete with motor and drive 7 which is
integrated into lower part, consisting of the clamp 11 and
the base 13, by means of the swivel support 9.
Here is a list of the main parts with the number indicating
it in the draw ing.
Legend Fig. 1
1. Command grip
2. Blade tension handwheel
4. Sliding blade guide
5. Machine body
6. Blade
7. Motor
8. Control box
9. Bar stop
10. Clamp (vice)
11. Morsa
12. Clamp drive
13. Base
WEIGHT: ................................................................. 17 Kg.
SIZE:................................ 85 x 36 x H65 cm. in maximum
PACKAGING SIZE: ..............................30 x 80 x H50 cm.
2

INSTALLATION

2.1 REMOVING THE PACKING
Remove the wooden frame which protects the machine
during transit.
Try not to damage the frame as you may have to move the
machine long distances or store it for long periods.
2.2 HANDLING (Fig. 2)
As the machine is not heavy (Kg. 17), it can be lifted and
moved by a single person by gripping it from the machine
body 5, duly clamped (see pint 2.3).
2.3 TRANSPORT (Fig. 2)
It is necessary to low the saw body till the lower position
and fi x it to the base : it is suffi cient to insert the pin U in
the hole in the body, then lift the machine, gripping it as
showed in Fig. 2.
For transport the machine, it is better to place it in the box
it was when purchased.
Ensure it is placed in the correct position indicated by the
arrows on the packaging.
Pay careful attention to the ideogram printed on the box
as they provide all necessary information for palletization
and stacking of boxes.
Tying the load down with ropes or safety belts is
raccomended during transportation to prevent the load
from sliding or falling.
2.4 POSITION/WORK STATION (Fig. 3)
Place the machine on a suffi ciently fl at workbench so that
the machine has the better possible stability. Should you
wish to fi x the machine in place, use the special holes
located on the base.
overall dimensions.