Specifications - Makita GA7030 Bedienungsanleitung

ENGLISH (Original instructions)
1-1. Shaft lock
2-1. Motor housing
2-2. Lock button
2-3. Handle
3-1. Switch trigger
3-2. Lock lever
5-1. Wheel guard
5-2. Screw
5-3. Bearing box
6-1. Wheel guard
6-2. Bearing box
6-3. Nut
6-4. Lever
7-1. Nut
7-2. Lever
8-1. Lock nut

SPECIFICATIONS

Depressed center wheel diameter
Max. wheel thickness
Rated speed (n)/ No load speed (n
• Due to our continuing program of research and development, the specifications herein are subject to change without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
Intended use
The tool is intended for grinding, sanding and cutting of
metal and stone materials without the use of water.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and
can only be operated on single-phase AC supply. They
are double-insulated and can, therefore, also be used
from sockets without earth wire.
For public low-voltage distribution systems of
between 220 V and 250 V.
Switching operations of electric apparatus cause
voltage fluctuations. The operation of this device under
unfavorable mains conditions can have adverse effects
to the operation of other equipment. With a mains
impedance equal or less than 0.23 Ohms it can be
presumed that there will be no negative effects. The
mains socket used for this device must be protected
with a fuse or protective circuit breaker having slow
tripping characteristics.
Explanation of general view
8-2. Depressed center wheel
8-3. Super flange
8-4. Inner flange
9-1. Lock nut wrench
9-2. Shaft lock
10-1. Lock nut
10-2. Abrasive disc
10-3. Rubber pad
12-1. Wire cup brush
13-1. Wire wheel brush
14-1. Lock nut
14-2. Abrasive cut-off wheel/diamond
14-3. Inner flange
14-4. Wheel guard for abrasive cut-off
Model
Spindle thread
)
0
Overall length
Net weight
Safety class
wheel
wheel/diamond wheel
GA7030/GA7030S
6.5 mm
6.0 kg
ENE048-1
Noise
The typical
according to EN60745:
ENF002-2
Model GA7030, GA7030S
Sound pressure level (L
Sound power level (L
Uncertainty (K) : 3 dB (A)
Model GA7040S, GA9030, GA9030S, GA9040S
ENF100-1
Sound pressure level (L
Sound power level (L
Uncertainty (K) : 3 dB (A)
4
15-1. Lock nut
15-2. Outer flange 78
15-3. Abrasive cut-off wheel/diamond
wheel
15-4. Inner flange 78
15-5. Wheel guard for abrasive cut-off
wheel/diamond wheel
16-1. Exhaust vent
16-2. Inhalation vent
17-1. Commutator
17-2. Insulating tip
17-3. Carbon brush
18-1. Brush holder cap
18-2. Screwdriver
GA7040S GA9030/GA9030S
180 mm
6.5 mm
M14
-1
8,500 min
511 mm
6.4 kg
/II
A-weighted noise
pA
) : 100 dB (A)
WA
pA
) : 101 dB (A)
WA
Wear ear protection
GA9040S
230 mm
6.5 mm 6.5 mm
M14
-1
6,600 min
511 mm
6.3 kg 6.7 kg
ENG905-1
level determined
) : 89 dB (A)
) : 90 dB (A)