Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
DISCONNECTING PTO DRIVESHAFT
Z Z
I I
- -
H H
S S
1 1
8 8
E E
Z Z
/ /
Z Z
Z
I
-
H
S
1
8
E
Z
/
1. Reduce tractor throttle to IDLE before dis-
engaging PTO. Apply the parking brake and
turn off the engine.
2. Pull up the locking pins and slide the lower
draft arms of the tractor off from the splitter
hookup pins.
3. Pull up the hitch pin and slide the upper
draft arm off from the mounting bracket.
4. Release the spring pins located on both
ends
of
the
driveshaft.
driveshaft off from the PTO shaft ends on the
gearbox and tractor respectively.
TRANSPORTATION
Z Z
I I
- -
H H
S S
1 1
8 8
E E
Z Z
/ /
Z Z
Z
I
-
H
S
1
8
E
Z
/
3-point attachment to tractor allows the log
splitter to be moved easily.
Allow for added length in
driving
situations,
when turning, parking, and
crossing intersections.
Before transporting, be cer-
tain the log splitter is cor-
rectly and securely attached
to the tractor and the safe
chains of the PTO are in
place. Make sure the log
splitter
is
raised
enough to clear all obstacles
during transportation. Never
transport
the
with the PTO engaged.
Hydraulische Holzspalter / Hydraulic log splitters ZI-HS13E/ZI-HS18EZ/ZI-HS25Z / ZI-HS25EZ
I I
- -
H H
S S
2 2
5 5
( (
E E
) )
Z Z
Z
I
-
H
S
2
5
(
E
)
Z
Slide
the
I I
- -
H H
S S
2 2
5 5
( (
E E
) )
Z Z
Z
I
-
H
S
2
5
(
E
)
Z
e.g.,
high
log
splitter
S
S
S
P
L
I
T
T
P
L
I
T
T
P
L
I
T
T
Z Z
I I
- -
H H
S S
1 1
Z
I
-
H
S
1
Plan your work site. Work safely and save
effort by planning your work before hand.
Have your logs positioned where they can be
easily reached. Have a site located to stack
the split wood or load it onto a nearby truck
or other carrier. Position the log splitter on
solid level ground.
Apply a thin coat of grease to the surfaces of
the ram before operation will lengthen the
durability of the ram.
PTO
Bleed the air out of the hydraulic system be-
fore starting the log splitter. The cover of the
hydraulic oil tank should be loosened by
some rotations until air can go in and out of
the oil tank smoothly.
Air flow thru the oil tank filler should be de-
tectable during the operations.
Before moving the log splitter, make sure the
cover of the oil tank is tightened to avoid oil
leaking from this point.
Failed to loosen the oil tank
cover will keep the sealed air in
hydraulic
pressed
pressed.
compression and decompression
will blow out the seals of the
hydraulic
permanent damage to the log
splitter.
O
O
O
E
R
P
E
R
A
T
I
O
E
R
P
E
R
A
T
I
O
E
R
P
E
R
A
T
I
O
3 3
E E
3
E
system
being
com-
after
being
decom-
Such
continuous
system
and
cause
N
N
N
air
Seite 39
Quicklinks ausblenden:
Werbung
Inhaltsverzeichnis
