Inhaltsverzeichnis
Werbung
Inserting the battery in the remote
control unit
1
Insert the battery as shown in the figure (make sure
to insert it with correct polarity as marked on the
bottom of the battery compartment).
If the receiver does no longer correctly correspond
1
to remote control commands, the battery might be
exhausted.
!
It is absolutely necessary to remove the exhausted
2
battery.
We can assume no liability for damage due to a
leaking battery.
3
4
5
Switching on
1
Switch on your television.
2
Switch on the receiver with one of the buttons
¢
,
¢
or
¢
on the receiver or one of the buttons
b
, ] or | on the remote control unit.
– The last selected programme appears automati-
cally (Last Station Memory).
or
use the numeric buttons
...
on the remote
6
control unit to directly enter the number of the de-
sired programme position.
7
– The receiver is automatically switched on with the
last selected channel index (favourite, radio or
normal index).
8
Switching off
Turn off the receiver by pressing the
button on
1
b
¢
the remote control unit or the
button on the
front of the receiver.
The receiver's display indicates "Standby
" if it
is in standby mode.
!
Unless you are disconnecting the power lead, the
receiver will not be disconnected from the mains
(see chapter "Installation and Security").
Tuning the TV set and video
recorder to the receiver
This adjustment can be omitted if you have con-
nected the receiver via a EURO-AV connecting lead
to the television or video recorder.
Select a free channel position on your TV and tune to
UHF channel 37 (the receiver's output channel). For
this, refer to the instruction book of your TV.
If this channel is already being used by a TV chan-
nel or a different unit (say, your video recorder),
you will see interference if the other equipment is
operating.
Retune your TV to an unused part of its range
(channel number 21 to 69).
Switch the receiver to standby using the
b
button
on the remote control unit or the
¢
button on its
front.
O
Press for approximately 6 seconds on the
button on the remote control. The receiver's display
indicates "CH
37".
Use the
c x
or the numeric buttons to tune the
receiver to the same channel as the TV receiver.
The "TV/VCR" modulator output (at the rear of the
receiver) delivers a test picture. This will assist you
in tuning to the corresponding channel on the TV
set. This is also possible if no satellite programme
is received.
Finetune the picture and sound on your TV receiver.
O
Press the
button to store the setting. The recei-
ver switches to standby. Pressing the
.
button
cancels the entry and recovers the old value.
The test picture is no longer emitted.
Tune in the same way a free programme position of
the video recorder to the receiver ouptut channel.
On-screen menu guide
When pressing the
button on the remote control
1
.
unit once, the STATUS menu appears briefly on the
picture screen.
STATUS
001
ARD
11494 GHZ H
7.02 7.20 MHZ PANDA
1
SUN
15:35
This status menu contains: the indication of the
active channel index (e.g. Favourite DEUTSCH), the
programme position number with the associated
station name, programme position settings (trans-
mission frequency of the satellite, polarization and
audio setting), day of the week and time.
2
Press the
.
button on the control unit twice.
– The "MAIN MENU" appears.
2
MAIN MENU
1 TIMER
2 INSTALL
3 CHANNEL SETUP
4 LOCK CONTROL
PRESS 1-4 OR I
3
Use the numeric buttons to call up the submenus.
4
Use the ] | buttons to select the data you wish
to change.
3
5
Use the
buttons (in some cases also the
x c
numeric buttons) to change the data.
6
Save the changed values by pressing the
O
button.
If the message "ARE YOU SURE?" is displayed, you
must press the
O
button once again if you really
wish to save the new setting.
7
Press the
button when you are in a menu to
,
A /B
display or not the TV picture.
8
To exit a menu, press the
button. You pass from
.
a submenu to the main menu or exit the main menu
without saving.
Language selection
You can choose between the following languages
for the on-screen menus:
"ENGLISH"
"DEUTSCH"
"ESPANOL"
"PORTUGUES"
"ITALIANO"
Press the
button on the remote control unit
.
twice.
– The "MAIN MENU" appears.
MAIN MENU
1 TIMER
2 INSTALL
3 CHANNEL SETUP
4 LOCK CONTROL
PRESS 1-4 OR I
Press the numeric button
and then the numeric
button
.
– The "INSTALL" and "LANGUAGE" menus appear
one after the other.
INSTALL
LANGUAGE
1 LNC SETUP
1 ENGLISH
2 DEUTSCH
2 CUSTOM AUDIO
3 ESPANOL
3 DECODER/AV
4 PORTUGUES
4 LANGUAGE
5 ITALIANO
PRESS 1-4 OR I
PRESS 1-5 OR I
Use the
...
buttons to select the desired
language.
– The selected language is automatically saved.
Werbung
Inhaltsverzeichnis
