Chainsaw Safety Warnings - Ryobi RCS2340 Originalanleitung

If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of dust collection
POWER TOOL USE AND CARE
Do not force the power tool. Use the correct power
tool for your application. The correct power tool will
do the job better and safer at the rate for which it was
designed.
Do not use the power tool if the switch does not turn
it on and off. Any power tool that cannot be controlled
with the switch is dangerous and must be repaired.
Disconnect the plug from the power source and/or
the battery pack from the power tool before making
any adjustments, changing accessories or storing
power tools. Such preventive safety measures reduce
the risk of starting the power tool accidentally.
Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power tool.
users.
Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may affect the power tool's
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
Keep cutting tools sharp and clean.
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
Use the power tool, accessories and tool bits etc,
in accordance with these instructions, taking into
account the working conditions and the work to
be performed. Use of the power tool for operations
different from those intended could result in a
hazardous situation.
SERVICE
Have your power tool serviced by a qualified repair
person using only identical replacement parts.
This will ensure that the safety of the power tool is
maintained.
ADDITIONAL GENERAL SAFETY WARNINGS
Some regions have regulations that restrict the use of
the product. Check with your local authority for advice.
Never allow children or people unfamiliar with the
instructions to use the product. Local regulations may
restrict the age of the operator.
Ensure before each use that all controls and safety
devices function correctly. Do not use the power tool if
the "off" switch does not stop the motor.
Wear full eye and hearing protection, strong sturdy
gloves as well as head protection while operating the
product; use a face mask if operation is dusty.
Do not wear loose fitting clothing, short trousers or
jewellery of any kind.
Secure long hair so it is above shoulder level to prevent
2 | English
entanglement in moving parts.
Beware of thrown, flying or falling objects; keep all
bystanders, children, and animals at least 15 m away
from work area.
Do not operate in poor lighting. The operator requires a
clear view of the work area to identify potential hazards.
Use of hearing protection reduces the ability to hear
extra attention to what is going on in the working area.
Operating similar tools nearby increases both the risk
of hearing injury and the potential for other persons to
enter your working area.
Keep firm footing and balance. Do not overreach.
Overreaching can result in loss of balance and can
increase the risk of kickback.
Keep all parts of your body away from any moving part.
Inspect the machine before each use. Check for correct
operation of all controls including the chain brake.
Check for loose fasteners, make sure all guards, and
handles are properly and securely attached. Replace
any damaged parts before use.
Do not modify the machine in any way or use parts
and accessories which are not recommended by the
manufacturer.
If you need to use an extension cable ensure it is
suitable for outdoor use and has a current capacity
sufficient to supply your tool, check it before every use
for damage, always uncoil it during use because coiled
cables can overheat.
A power spike causes voltage fluctuations and may
affect other electrical products in the same power
line. Connect the product to a power supply with an
Contact your electric power supplier for further
clarification.
If the machine is dropped, suffers heavy impact or begins
to vibrate abnormally, immediately stop the machine and
inspect for damage or identify the cause of the vibration.
Any damage should be properly repaired or replaced by
an authorised service centre.

CHAINSAW SAFETY WARNINGS

Keep all parts of the body away from the saw chain
when the chainsaw is operating. Before you start
the chainsaw, make sure the saw chain is not
contacting anything. A moment of inattention while
operating chainsaws may cause entanglement of your
clothing or body with the saw chain.
Always hold the chainsaw with your right hand
on the rear handle and your left hand on the front
handle. Holding the chainsaw with a reversed hand
configuration increases the risk of personal injury and
should never be done.
Hold the power tool by gripping surface only,
because the saw chain may contact hidden wiring
WARNING