Scheppach HD2P Betriebsanweisung Seite 12

■ INSERTING/REPLACING THE DUST BAG, FIG. 2/3
Open both clamps (3) and fold the case cover
backwards. Open the lid for the dust bag (10),
press the clamping bracket (12) on the dust
bag and push it over the suction nozzle.
■ SUCTION FUNCTION FIG. 4-7
Remove the power plug for all conver-
sions.
When using the suction function, always
insert a dust bag. The connection nozzle (14)
must be inserted on the side of the dust bag.
■ FUNCTION: BLOWING OUT, OFF AND UP FIG. 4-7
The conversion of the device for blowing out
can be done in a few simple steps.
Remove the connection nozzle (14) from the
suction side and insert on the opposite side.
(17)
■ NOTES ON THE USE OF BOREHOLE-SUCTION NOZZLE FIG.8
Attach the drill suction nozzle (9) to the suction
hose.
■ USE OF THE INFLATION NOZZLE FIG. 9-10
The suction-blowing nozzle (7) can be used
for suction or inflating of suitable objects. Set
the suction device to blowing mode.
GB
Connections and repair work on the electrical
equipment may be carried out only by a quali-
fied electrician. The installed electric motor is
connected and ready for use. The connection
complies with the relevant VDE and DIN reg-
ulations. The connection to the mains supply
provided by the customer as well as the exten-
sion cables must comply with these regula-
tions.
Important notes
Faulty electric connecting cables
The electric connecting cables often have insu-
lation damages.
Possible reasons are::
• Pressure marks if connecting cables are fed
through window or door gaps.
• Kinks due to improper fastening or passing of
the connecting cable.
Assembly
Close the lid again until it clicks into place.
When you empty a full dust bag, clean the
dust bag chamber with a moist cloth or brush
before you inserting it again.
(16) Insert the suction grating with filter on the
opposite side. Make sure both parts click into
place. Insert the suction hose (6) with the lug
into the connection nozzle (14) and lock in it
place by rotating it slightly.
Insert suction grating with filter on the suction
side. Connect the suction hose and attach
the blowing nozzle (7).
Keeping the hole on the jet nozzle closed will
increase the blowing pressure.
Switch on the suction device and place the
drill suction nozzle onto the borehole.
Place the suction-blowing nozzle onto the
suction hose.
Switch the suction device on.
Electrical Connection m
• Cutting points due to driving over connecting
cables.
• Insulation damages due to ripping cables out
of the wall socket.
• Cracks due to aging of the insulation.
Electric connection cables that are damaged in
this way may not be used and due to insulation
damages, they constitute a danger to life.
Check electric cables for damages regularly.
Make sure the connection cable is not con-
nected to the power supply while checking it.
Electric connection cables must comply with
the relevant VDE and DIN regulations. Only
use connection cables with the H05VV-F mark-
ing.
12
Pass the connection cable through the notch
(a) on the front. Close the case cover and lock
it with both clamps.
Attach a jet nozzle onto the suction hose;
connect the mains plug and press the on
button.
Do not point the air flow at persons or ani-
mals.
Due to the vacuum, the nozzle sticks to level
surfaces.
By covering the borehole (a) on the nozzle,
you can regulate the airflow
The norm stipulates that there must be a type
designation imprint on the connection cable.
AC motor
• The mains voltage must correspond to the
mains voltage indicated on the type plate.
• Extension cables must have a minimum cable
cross section of 1.0 square millimetres.
• The mains supply must be secured by a suit-
able fuse.
In case of questions, please indicate the
following information:
• Motor manufacturer
• Type of motor's current
• Data on the machine type plate
• Data on the switch type plate
If you return a motor, always send back the en-
tire drive unit with switch.