Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Warning!
Wear and take off the helmet after every assembly to see if it fits correctly.
Additional details that helps to improve general comfort:
4c.Anatomical inner shell: Designed taking into account the average measure of the skull and personalized thanks to Airoh experience,
the inner shell has wide air channels on the inside, together with appropriate vents on the inner comfort liner, which facilitate excellent
inner helmet climate control and comfort.
4d.Low weight, --Low noise inside the helmet: Thanks to the innovative materials used, the load on the neck and the noise, especially
in extreme conditions, are reduced to a minimum.
4e.Complete adjustable ventilation: It is better described in the specific paragraph; it improves the helmet climate control by increasing
ventilation and general comfort.
5.. Wind Stop Device
Fig.13
Easily removable device, it limits cold air penetration from the bottom and reduces inner noise. It is particularly suitable on cold days and in
winter. If there is a Wind Stop Device, remove it by pulling it downwards,
between the edge and the chin guard and push towards the inside of the helmet until it locks into place, as shown in
6.. Nose Deflector
The particular shape of this device conveys the air and humidity coming out of the mouth downwards, reducing the production of
condensation on the inner surface of the visor. The device is clipped on and can be easily removed,
7.. Complete Integrated Ventilation
Fig.15
The inner ventilation of this helmet is the result of aerodynamic research in the wind tunnel and of Airoh experience during races directly.
The system is visible from the outside thanks to the 10 air ducts perfectly integrated and located to reach the best performance. It is also
located inside the shell, thanks to the air ducts that enable and guarantee optimized air exchange and comfort. The adjusting devices,
located on air ducts and easy to use even when wearing gloves, allow adjusting the opening of the air intakes to optimize the ventilation
and modify it according to the weather conditions.
A
--Adjustable Upper Front Aerator, for Air Intake.
It conveys the fresh air directly towards the upper intake ports of inner air ducts. To open the air intake flow, push the slider forwards
Fig.15A
.
B
--Adjustable Lower Front Aerators, for Air Intake.
They convey the fresh air directly towards the lower intake ports of inner air ducts. To open the air intake flow, push the sliders towards the
Fig.15B
outside of the helmet
.
C
--Rear Extractors. Directly connected to the inside of the shell, they are shaped so as to act both as a stabilising spoiler and an air
extractor. The first function is the air extraction thanks to the direct connection with the inner air ducts. The second function reduces
turbulence on the back side of the helmet. The rear extractors and the particular shape of the shell in that position drastically reduce the
Fig.15C
noise, by acting as spoiler
.
D
Side Extractors. They facilitate the extraction of hot humid air from the lower part of the helmet. Moreover, air flows in that area are
Fig.15D
optimized and they reduce the noise perceived
E
--Chin Guard Aerators. They convey fresh air and create an air flow on the inner surface of the visor and on the rider mouth,
guaranteeing a constant air circulation and reducing the production of condensation and the fogging of the visor.
The various combinations available allow you to adjust the system to suit any weather condition, thus always assuring superior comfort.
see Fig. 13A.
To assemble it, insert the flap in the fastening hole
see Fig.14.
.
16
8.. Lower Protection Trim with Lower Integrated Stabilisers
The lower protection trim made of rubber protects the lower edge of the helmet. The integrated front and rear spoilers improve
helmet stability by reducing turbulence, especially at high speed, and thus allowing also to reduce the vibrations and the noise
inside the helmet.
9.. Top Painted Surface
The painted and UV-coated outer shell guarantees higher resistance on the surface and preserve the shine of its colour over
time.
Fig.16
, Locatelli S.p.A. accepts no liability for damages resulting from falls, even accidental ones, that could cause dents and/or
abrasions.
10.. Accessories and Spare Parts
The helmet is sold in the standard shape available in the original packing. Model specific spare parts - indicated in
be purchased at your Airoh dealer.
Warning!
Only use helmet specific spare parts of the Airoh after sale service.
Fig.13B
.
Warning!
Non-compliance with the above-mentioned instructions shall release Locatelli S.p.A. from any responsibilities in case of
improper use of the helmet.
Fig.17
17
- may
Werbung
