Editing A Program; Selecting The Projectors In The Program; Inverting The Pan/Tilt Movement; Records - Futurelight CP-256/32 Bedienungsanleitung

button and check every scene individually by pressing the respective projector select button.

6.5.4 Editing a program

Should you notice that a scene does not correspond to your imagination or when programs have to be edited
for a new stage, it is necessary to modify a scene manually.
First note the total number of steps. Press the Menu-button and and select "Menu 2 Make Prog." via the
Up/Down-buttons or the Data Entry fader. Press the Enter-button twice. Select the desired program via the
projector select buttons.
Select the desired scene via the Up/Down-buttons. If you hold the Recall-button and press the Up/Down-
button at the same time, the current scene is shown. Select the desired projector via the projector select
buttons. Adjust the desired settings via the encoders and the respective channel faders. Select the next
projector via the projector select buttons and adjust the settings. Press the Enter-button in order to save the
edited step. Edit the next steps until the program is finished.
Caution: Before leaving the Edit-Mode, the last step of the program has to be saved another time.
Otherwise, the program will not run correctly.
Select the last scene via the Up/Down-buttons. Press the Recall-button in order to show the memorized
scene. Save this scene by pressing the Enter-button. Press the Escape-button and the Enter-button in order
to save the edited program.

6.5.5 Selecting the projectors in the program

The number of projectors to be used in a program can be individually adjusted for every program.
Press the Menu-button and and select "Menu 2 Make Prog." via the Up/Down-buttons or the Data Entry
fader. Press the Enter-button. Select the menu "Edit Mask" via the Up/Down-buttons and press the Enter-
button.
Select the desired projector via the Projector Select button. All project numbers marked with "*" are activated
in the program and the respective Projector Select button flashes. If you wish to remove certain projectors
from the program, press the respective Projector Select button. The LED turns off and the display shows "X".
Press the Enter-button twice in order to save the settings.

6.5.6 Inverting the Pan/Tilt movement

The Pan and Tilt movement of a scanner can be inverted for every program. This function is particularly
useful if scanners are installed face to face in the room and a synchronic movement is desired.
Caution: Please note that the inverting of the Pan/Tilt movement has to be adjusted before you start
programming.
Press the Menu-button and and select "Menu 2 Make Prog." via the Up/Down-buttons or the Data Entry
fader. Press the Enter-button. Select the menu "Make Program Mirror Direction" via the Up/Down-buttons
and press the Enter-button.
Select the desired projector via the Projector Select button. All project numbers marked with "->" have the
normal Pan-direction. If you wish to invert the Pan-movement for certain projectors, press the respective
Projector Select button. The display shows "<-" for the projector with inverted Pan-movement.
Press the Down-button in order to invert the Tilt-movement.
Press the Escape-button in order to return to the menu "Make Program2. Program your program now.

6.6 Records

A record is a sequence of different programs that will be called up one after another. With the CP-256/32,
you can program up to 32 different records which can be assigned to the projector select buttons 1-32.

6.5.1 Programming a Record

Press the Menu-button and select "Menu 1 Make Record" via the Up/Down-buttons or the Data Entry fader.
Press the Enter-button. Select the desired record via the projector select buttons. The display shows the
Step-number and the respective program, the program speed and the repition rate or sound-control.
Adjust the desired program via the projector select buttons. Adjust the program speed and the repition rate
via the Speed-control or Rate-control or activate the sound-control via the Music-button.
Select the next step via the Up/Down-buttons or the Data Entry fader and enter the desired program via the
projector select buttons. Program the next steps until the record is finished or the maximum number of steps
- 99 - has been reached. Press the Escape-button and the Enter-button in order to save the record.
33