Functional Description - Makita 5704R Bedienungsanleitung

FUNCTIONAL DESCRIPTION

CAUTION:
Always be sure that the tool is switched off and
•
unplugged before adjusting or checking function on
the tool.
Adjusting depth of cut
Fig.1
CAUTION:
After adjusting the depth of cut, always tighten the
•
lever securely.
Loosen the lever on the depth guide and move the base
up or down. At the desired depth of cut, secure the base
by tightening the lever.
For cleaner, safer cuts, set cut depth so that no more
than one blade tooth projects below workpiece. Using
proper cut depth helps to reduce potential for dangerous
KICKBACKS which can cause personal injury.
Bevel cutting
Fig.2
Loosen the clamping screws in front and back, and tilt the
tool to the desired angle for bevel cuts (0° - 45°). Secure
the clamping screws tightly in front and back after making
the adjustment.
Sighting
Fig.3
For straight cuts, align the A position on the front of the
base with your cutting line. For 45° bevel cuts, align the B
position with it.
Riving knife adjustment
Fig.4
Use the hex wrench to loosen the hex socket head bolt for
the riving knife adjustment, then raise the lower blade guard.
Move the riving knife up or down over the two protuberances
for settings indicated in the figure, so as to obtain the proper
clearance between the riving knife and saw blade.
CAUTION:
Ensure that the riving knife is adjusted such that:
•
The distance between the riving knife and the
toothed rim of the saw blade is not more than 5 mm.
The toothed rim does not extend more than 5 mm
beyond the lower edge of the riving knife.
Switch action
Fig.5
CAUTION:
Before plugging in the tool, always check to see
•
that the switch trigger actuates properly and returns
to the "OFF" position when released.
To prevent the switch trigger from being accidentally
pulled, a lock-off button is provided. To start the tool,
push in the lock-off button and pull the switch trigger.
Release the switch trigger to stop.
ASSEMBLY
CAUTION:
Always be sure that the tool is switched off and
•
unplugged before carrying out any work on the tool.
Removing or installing saw blade
The following blade can be used with this tool.
Max. dia. Min. dia. Hole dia.
190 mm 170 mm 20 mm or 30 mm
006483
The thickness of the riving knife is 1.8 mm.
CAUTION:
Do not use saw blades which do not comply with
•
the characteristics specified in these instructions.
Do not use saw blades the disc of which is thicker
•
or the set of which is smaller than the thickness of
the riving knife.
Fig.6
CAUTION:
Be sure the blade is installed with teeth pointing up
•
at the front of the tool.
Use only the Makita wrench to install or remove the
•
blade.
To remove the blade, press the shaft lock fully so that the
blade cannot revolve and use the wrench to loosen the
hex bolt counterclockwise. Then remove the hex bolt,
outer flange and blade.
To install the blade, follow the removal procedure in
reverse. BE SURE TO TIGHTEN THE HEX BOLT
CLOCKWISE SECURELY.
Fig.7
When changing blade, make sure to also clean upper
and lower blade guards of accumulated sawdust. Such
efforts do not, however, replace the need to check lower
guard operation before each use.
CAUTION:
The inner flange has a 30 mm diameter on one side
•
and a 20 mm diameter on the other. The side with
20 mm diameter is marked by "20". Use the correct
side for the hole diameter of the blade you intend to
use. Mounting the blade on the wrong side can
result in dangerous vibration.
Connecting a vacuum cleaner
Fig.8
When you wish to perform clean cutting operation,
connect a Makita vacuum cleaner to your tool. Install the
joint on the tool using the screws. Then connect a hose of
the vacuum cleaner to the joint as shown in the figure.
7
Blade thickness Kerf
less than 1.7 mm more than 1.9 mm