Specifications; Additional Safety Rules For Tool - Makita 6960D Betriebsanleitung

ENGLISH
1 Button
2 Battery cartridge
3 Charging light
4 Fast charger
5 Bit
6 Sleeve

SPECIFICATIONS

Model
Capacities
Wood screw ................................. ø3.5 mm – ø9.5 mm
-1
No load speed (min ) ...................................... 0 – 2,500
Impacts per minute .......................................... 0 – 1,600
Fastening torque ................................................. 30 N . m
Overall length ..................................................... 195 mm
Net weight ............................................................. 1.8 kg
Rated voltage .................................................. D.C. 12 V
• Due to the continuing program of research and devel-
opment, the specifications herein are subject to change
without prior notice.
• Note: Specifications may differ from country to country.
Safety hints
For your own safety, please refer to enclosed safety
instructions.
IMPORTANT SAFETY INSTRUCTIONS FOR
CHARGER & BATTERY
CARTRIDGE
1. SAVE THESE INSTRUCTIONS — This manual
contains important safety and operating instruc-
tions for battery charger.
2. Before using battery charger, read all instructions
and cautionary markings on (1) battery charger,
(2) battery, and (3) product using battery.
3. CAUTION — To reduce risk of injury, charge only
MAKITA type rechargeable batteries. Other types
of batteries may burst causing personal injury
and damage.
4. Do not expose charger to rain or snow.
5. Use of an attachment not recommended or sold
by the battery charger manufacturer may result in
a risk of fire, electric shock, or injury to persons.
6. To reduce risk of damage to electric plug and
cord, pull by plug rather than cord when discon-
necting charger.
7. Make sure cord is located so that it will not be
stepped on, tripped over, or otherwise subjected
to damage or stress.
8. Do not operate charger with damaged cord or
plug — replace them immediately.
9. Do not operate charger if it has received a sharp
blow, been dropped, or otherwise damaged in any
way; take it to a qualified serviceman.
10. Do not disassemble charger or battery cartridge;
take it to a qualified serviceman when service or
repair is required. Incorrect reassembly may
result in a risk of electric shock or fire.
11. To reduce risk of electric shock, unplug charger
from outlet before attempting any maintenance or
cleaning. Turning off controls will not reduce this
risk.
Explanation of general view
7 Switch trigger
8 Reversing switch lever
9 A side
10 B side
11 Clockwise
12 Counterclockwise
12. The battery charger is not intended for use by
6960D
13. Young children should be supervised to ensure
14. If operating time has become excessively shorter,
15. If electrolyte gets into your eyes, rinse them out
ADDITIONAL SAFETY RULES FOR CHARGER
& BATTERY CARTRIDGE
1. Do not charge battery cartridge when temperature
2. Do not attempt to use a step-up transformer, an
3. Do not allow anything to cover or clog the charger
ENC001-3
4. Always cover the battery terminals with the bat-
5. Do not short the battery cartridge:
6. Do not store the tool and battery cartridge in
7. Do not incinerate the battery cartridge even if it is
8. Be careful not to drop, shake or strike battery.
9. Do not charge inside a box or container of any
ADDITIONAL SAFETY RULES
FOR TOOL
1. Be aware that this tool is always in an operating
2. Hold tool by insulated gripping surfaces when
13 Screw
14 Set plate
15 Limit mark
16 Screwdriver
17 Brush holder cap
young children or infirm persons without super-
vision.
that they do not play with the battery charger.
stop operating immediately. It may result in a risk
of overheating, possible burns and even an explo-
sion.
with clear water and seek medical attention right
away. It may result in loss of your eyesight.
is BELOW 10°C (50°F) or ABOVE 40°C (104°F).
engine generator or DC power receptacle.
vents.
tery cover when the battery cartridge is not used.
(1) Do not touch the terminals with any conduc-
tive material.
(2) Avoid storing battery cartridge in a container
with other metal objects such as nails, coins,
etc.
(3) Do not expose battery cartridge to water or
rain.
A battery short can cause a large current flow,
overheating, possible burns and even a break-
down.
locations where the temperature may reach or
exceed 50°C (122°F).
severely damaged or is completely worn out. The
battery cartridge can explode in a fire.
kind. The battery must be placed in a well venti-
lated area during charging.
condition, because it does not have to be plugged
into an electrical outlet.
performing an operation where the cutting tool
may contact hidden wiring. Contact with a ''live''
wire will also make exposed metal parts of the
tool ''live'' and shock the operator.
ENB024-1
3