Specifications - Makita 4604D Betriebsanleitung

ENGLISH
1 Charger DC4600
2 Charging light
3 Start button
4 Battery 4600
5 Charging plug
6 Charging connector
7 Restart button
8 Controller C4600
9 Switch
0 Buckle
q Pilot lamp

SPECIFICATIONS

Model
Max. cutting capacity .................. 30 mm in diameter
Overall length ............................................... 286 mm
Rated voltage ............................................ D.C. 24 V
Net weight
Shears .......................................................... 1.0 kg
Controller C4600 .......................................... 0.3 kg
Battery 4600 ................................................. 2.0 kg
Charging time ....................................... Approx. 1 hr.
• Due to our continuing program of research and
development, the specifications herein are subject
to change without notice.
• Note: Specifications may differ from country to
country.
Safety hints
For your own safety, please refer to the enclosed
safety instructions.
IMPORTANT SAFETY INSTRUCTIONS
FOR CHARGER & BATTERY
1. SAVE THESE INSTRUCTIONS — This manual
contains important safety and operating
instructions for battery charger.
2. Before using battery charger, read all instruc-
tions and cautionary markings on (1) battery
charger, (2) battery, and (3) product using
battery.
3. CAUTION — To reduce risk of injury, charge
only MAKITA type rechargeable batteries.
Other types of batteries may burst causing
personal injury and damage.
4. Do not expose charger to rain or snow.
5. Use of an attachment not recommended or
sold by the battery charger manufacturer may
result in a risk of fire, electric shock, or injury
to persons.
6. To reduce risk of damage to electric plug and
cord, pull by plug rather than cord when dis-
connecting charger.
7. Make sure cord is located so that it will not be
stepped on, tripped over, or otherwise sub-
jected to damage or stress.
8. Do not operate charger with damaged cord or
plug — replace them immediately.
Explanation of general view
w Waist belt
e Pocket lid
r Controller connector
t Waist belt pocket
y Suspenders
u Holster
i Arm band
o Connection cord
p Female plug
a Switch trigger
s Lock-off lever
9. Do not operate charger if it has received a
4604D
10. Do not disassemble charger or battery; take it
11. To reduce risk of electric shock, unplug
ADDITIONAL SAFETY RULES FOR
CHARGER & BATTERY
1. Do not charge battery when it or air tempera-
2. Do not charge or leave battery in a location
3. Do not attempt to use a step-up transformer,
4. Do not allow anything to cover or clog the
5. Do not short the battery:
6. Do not incinerate the Battery even if it is
7. Be careful not to drop, shake or strike battery.
8. Do not charge inside a box or container of any
d Upper shear blade
f Lower shear blade
g Branch
h Hex wrench
j Blade cover
k Socket wrench
l Blade holder
; Magnet
z Brush
x Machine oil
c Diamond file
sharp blow, been dropped, or otherwise dam-
aged in any way; take it to a qualified service-
man.
to a qualified serviceman when service or
repair is required. Incorrect reassembly may
result in a risk of electric shock or fire.
charger from outlet before attempting any
maintenance or cleaning. Turning off controls
will not reduce this risk.
ture is below 10°C (50°F) or above 40°C
(104°F).
exposed to direct sunlight.
an engine generator or DC power receptacle.
charger vents.
(1) Do not touch the terminals with any con-
ductive material.
(2) Avoid storing battery in a container with
other metal objects such as nails, coins,
etc.
(3) Do not expose battery to water or rain.
A battery short can cause a large current flow,
overheating, possible burns and even a break-
down.
Always cover the battery terminals with the
battery cover when the battery is not used.
severely damaged or is completely worn out.
The battery can explode in a fire.
kind. The battery must be placed in a well
ventilated area during charging.
7