Inglesina zippy Benutzerhandbuch Seite 16

GB
16
OPENING THE STROLLER
1 Pull the latch trigger (A) on the right-hand handle
upwards, then open the stroller by pulling the handle
itself upwards.
2 Give the handle a sharp, upward tug to click the
lower latches into position.
3 To complete opening press down on the central
locking mechanism (B) with your foot as illustrated
until it locks horizontally.
4 Make sure that all closure mechanisms are properly
locked on both sides before use.
CLOSING THE STROLLER
5 First of all, raise the backrest to its vertical position.
Press the red button (C) on the handle.
6 Lift the handle (D) and give it a sharp upwards tug
until the closure latch (E) on the right-hand handle
clicks onto the central coupling.
7 Warning: Make sure that the closure latch
(E) is correctly hooked onto the central coupling
as illustrated in the diagram.
REAR WHEEL BRAKE
8 To set the brake push the levers (G), on the rear
wheels, downwards with your foot.
To ensure your child's safety at all times always
set the brake when you stop and always make
sure the brake is locked in place.
FRONT WHEEL LOCK-RELEASE MECHANISM
9 The frame is fitted with swivel wheels which can
be locked in place or released simply by acting on lever
(F) on the front wheels.
REAR FOOTREST
10 Act with the foot on the rear platform to ease the
passing of hindrances.
HOOKING OF THE ADDITIONAL TRANSPORT
UNITS TO THE FRAME
(BAG AND CAR SEAT)
11 It is possible to hook the Zippy bag or the Huggy
car seat to the frame. For the correct fastening
procedure, see the dedicated instruction manuals.
HOOKING OF THE BACKREST TO CONVERT THE
FRAME INTO A STROLLER
12 It is possible to hook the backrest with the padding
(H) to the frame to obtain the stroller configuration.
13 Position the backrest on the frame. Insert the
two ends (L) in their seats (M) on both sides of the
INSTRUCTIONS
stroller.
14Then, insert the two ends (N) of the backrest
adjusting device in their proper seats (O) on both
sides of the stroller.
15Insert the string (P) in its seat located in the rear
part of the seat support.
16Insert the buckle of the leg separator in its proper
seat positioned in the front part of the seat support.
17Insert the levers (Q) of the footrest in the proper
holes on the padding.
18Fasten the armrest cover (R) in its proper seat.
Before sitting the child in the stroller, always make sure
that the cover is correctly attached to the armrest.
The cover coupling device also allows accessories to
be fitted (see accessory instructions).
19The armrest cover (R) can be removed to allow
the hooking of the bag and car seat also in the stroller
version. Push upwards from underside of armrest. To
refit the cover slide the front part onto the slot on the
armrest and press downwards.
HOW TO ADJUST THE BACKREST
20It is possible to adjust the backrest in 4 different
positions. To lower it, act on the central mechanism
(S) on the backrest itself and lower it to the desired
position. To raise it, instead, just push the backrest
upwards and it will lock into place automatically.
INSERT AND/OR REMOVE THE HANDRAIL
21Insert the pin of the handrail in the cavity on the
armrest and then push it inside until it clicks indicating
that it has been fastened.
Caution: Do not insert the fingers in the
handrail opening when these operations are
being carried out.
22The rail can be opened on one side only or
removed completely. To open press the red lever
under the armrest. To remove completely, do the same
on the other side.
FOOTREST ADJUSTMENT
23To lower the footrest slide both the levers (T) (in
the lower part of the footrest itself) forwards while
simultaneously pushing the footrest downwards. To
raise the footrest just pull it upwards: it will lock in
place automatically.
SEAT BELT
24Hook up the shoulder strap clips to the buckle
eyelets. Hook the ends of the waist strap to the central
buckle. The waist strap must always be inserted in the