Characteristics Noise Values; Operating Times; Symbols Machine / Operating Manual; Normal Intended Use - ATIKA BWS 600 Originalbetriebsanleitung

Characteristics noise values

DIN EN ISO 3746 / DIN EN ISO 11202 / ISO 7960 Appendix A
Use of the machine as log saw for firewood with standard saw blade.
Noise power level
(Load)
BWS 600
L = 105 dB(A)
WA
BWS 700
The factor of measurement uncertainty is 4 dB.
The values given are emission values and must therefore not simultaneously
represent safe workplace values too. Although there is a relationship between
emission and immersion levels, it can be reliably deduced whether additional
precautionary measures are necessary or not. Factors, which can influence the
immersion level currently existing at the workplace include the duration of the
effects, the special type of the workroom, other noise sources, etc. e.g. the
number of machines and other adjacent processes. The permissible workplace
values can also vary from country to country. This information should however
enable an improved assessment of the danger and risk to be carried out.

Operating times

Before initiating the device please observe the provisions pertaining to
corresponding laws (regional provisions) for the noise control.
Symbols machine
Carefully read opera-tor's
manual and the safety
instructions
starting the machine and
observe the instructions
when operating.
Risk of injuries of fin-gers
and hands by the saw
blade
Wear eye and
protection
Wear a face mask.
Electrical devices do not go into the domestic rubbish.
Give devices, accessories and packaging to an eco-
friendly recycling.
According to the European Directive 2002/96/EC on electrical and
electronic scrap, electrical devices that are no longer serviceable
must be separately collected and brought to a facility for an
environmentally compatible recycling.
Symbols operating instructions
Threatened hazard or hazardous situation. Not observing
this instruction can lead to injuries or cause damage to
property.
Important information on proper handling. Not observing
this instruction can lead to faults.
User information. This information helps you to use all the
functions optimally.
Assembly, operation and servicing. Here you are explained
exactly what to do.
, Please refer to the attached assembly and operating instruction
,
sheet for references to figure numbers in the text.
,
Sound pressure level at the workplace
(Load)
L = 96 dB(A)
PA
Shut off engine and
remove power
be-fore before
cleaning, maintenance
or repair work.
Wear protective gloves!
ear Wear safety shoes
Warning of hot sur-
faces. Danger of bur-
ning!
Do not touch hot engine parts.

Normal intended use

This machine is designed for cross cutting firewood in the house and
hobby field.
Cutting round material having a diameter over
190 mm – BWS 600
240 mm – BWS 700
is not allowed as these pieces can not be held safely.
The length of the material to be cut must not exceed 1000 mm. The
length of the material must be 200 mm as a minimum.
Only high-quality saw blades acc. to EN 847-1 up to a max. diameter of
600 mm – BWS 600
700 mm – BWS 700
must be used.
Because it has no extraction device this machine must only be used
outdoors.
Only work pieces are allowed to be processed which can be safely placed
and held in the jigging device.
The use of saw blades made of HSS steel (high-alloy high speed steel) is
not permitted since this steel is hard and brittle. Risk of injury through saw
blade breakage and expulsion of saw blade pieces.
The intended usage also includes compliance with the operating,
servicing and repair conditions prescribed by the manufacturer and
following the safety instructions included in the instructions.
The relevant accident prevention regulations for the operation as well as
the other generally acknowledged occupational medicine and safety rules
must be complied with.
Any other use is deemed not to be intended use. The manufacturer is not
liable for any type of damage resulting from this: the user bears the sole
risk.
cord
Unauthorized modifications to the saw preclude any liability of the
performing
manufacturer for resulting damages of any kind.
The saw may only be equipped, used and serviced by persons who are
familiar with it and have been instructed on the hazards. Repair works
may only be carried out by us or by a customer service agent nominated
by us.
The machine may not be used in a potentially explosive environment or
be exposed to rain.
Metallic parts (wires etc.) have unconditionally to be removed from the
material to be cut.

Risidual risks

Even if used properly, residual risks can exist even if the relevant safety
regulations are complied with due to the design determined by the intended
purpose.
Residual risks can be minimised if the "Safety instructions" and the "Normal
intended use" as well as the whole of the operating instructions are observed.
Observing these instructions, and taking proper care, will reduce the risk of
personal injury or damage to the equipment.
Danger of injury of fingers and hands by the tool (saw blade) or work piece,
e.g. when replacing the saw blade.
Injury by catapulted workpiece parts.
Throwback of the workpiece or workpiece parts.
Breaking or catapulting of saw blade.
Risk from electricity, by using non-standard electrical connections.
Touching live parts of opened electrical components.
Impairment of hearing when working on the machine for longer periods of
time without ear protection.
In addition, in spite of all the precautionary measures taken, non-obvious
residual risks can still exist.
11