Pojistné Háky; 365066 Sikringskrok; 365066 Säkringskrok; Working With The Saw - ATIKA BWS 600 Originalbetriebsanleitung

On/Off switch
Do not use any device where the switch can not be switched on and off.
Damaged switches must be repaired or replaced immediately by the
customer service.
Switching on
Press the green button on the
switch.
If there is a power cut, the
machine switches off automati-
cally. Push the green button to
start the m chine again. a
Switching off
Press the red button (O). The
built-in brake will decelerate the
saw blade up to the dead stop
within 10 seconds.
The saw must not be used if the brake is defective, i.e. if the time
from switching off up to the saw blade's dead stop exceeds
10 seconds.
Motor guard
The motor is equipped with a guard switch and it switches off
automatically when overload. The motor can be switched on again
after a cooling-down period (approx. 5 – 10 mins.).

Working with the saw

Before starting to work consider the following safety advices to keep the
risk of injuries as small as possible.
Saw blade, plastic inserts, recuperating spring o. k.
Workplace tidied?
You may not start to operate the machine until you have read these
operating instructions, observed all the instructions given and installed
the machine as described!
Before making adjustments to the saw settings (e.g. replacing the saw
blade etc.)
− switch off device
− wait for standstill of the saw blade.
− pull out power plug
Also, note the following important points:
Place yourself outside of the area of danger.
Place the wood piece in the jigging device. Cut through the piece with
uniform pressure.
Never remove loose splinters, chips, or similar by hand.
At any case pay attention to all safety instructions.

Working instructions

1. Secure the saw against rolling away.
2. Place the wood piece in the jigging device.
Only wood pieces with a max. diameter of
190 mm – BWS 600
240 mm – BWS 700
are allowed to be sawed.
3. Hold the handle (14) on the jigging device with both hands and push the
jigging device uniformly towards the saw blade. Avoid erratic movements.
The barbs on the jigging device prevent any turning of the wood
piece during sawing.
Do not force the jigging device against the saw blade, the motor
speed should not drop too far.
4. After cutting, the jigging device is automatically brought back to its home
position by spring force.
14
If the recuperating spring (11) is broken or worn, the jigging device
will not automatically return to its home position. Replace the
recuperating spring. See "Replacing the return spring".
Never saw without or with a damaged recuperating spring.
5. Only advance the wood piece after a completed sawing operation.

Maintenance and cleaning

Before each maintenance and cleaning work
− Switch off device
− Wait unitl the saw blade comes to a stop
− Pull out power plug
Maintenance and repair work other than those described in this chapter is
only allowed to be carried out by service staff.
For maintaining and cleaning, removed security devices must unconditionally
be mounted properly and proved again.
Use only original parts. Other parts can result in unexpected damages and
injuries.
Cleaning
Observe the following to maintain the operability of the machine:
Do not wash down device with water.
Remove shavings and dust only with a brush or vacuum cleaner.
Clean and oil all moving parts regularly.
Never use any grease!
Use for instance sewing machine oil, liquid hydraulic fluid or
environmentally acceptable spray oil.
Take care that the saw blade remain free of rust and resin.
Remove resin residues from the push frame surface.
Resin residues can be removed with a commercial maintenance and care
spray.
The saw blade is a wearing part and will become dull after prolonged or
frequent use.
Renew the saw blade or have it sharpened
Maintenance

Changing the saw blade

Remove the mains plug before changing the saw
blade.
Danger of cutting! The saw blade is massive and it could be to slick.
Wear gloves when replacing the saw blade.
Do not use any saw blades made of HSS steel.
Do not use any cracked saw blades or such that have changed their
shape.
Only use well-sharpened saw blades.
Danger of burning! The saw blade is still hot shortly after cutting.
1. Pull out the spring cotter pin (4). When doing so, firmly hold the tilt
table.
2. Slowly lower the tilt table towards the ground.
3. Use the locking pin (13) to secure the saw blade (5) against turning.
4. Loosen the screw (6).
5. Remove the washer (7), the front saw blade flange (8) and the saw blade
(5).
6. Clean the saw blade flanges (8, 15).
7. Install a new or sharpened saw blade.
.