Charging The Battery - Black & Decker CD12 Bedienungsanleitung

on the ways in which the tool is used. The vibration level may
increase above the level stated.
When assessing vibration exposure to determine safety
measures required by 2002/44/EC to protect persons regularly
using power tools in employment, an estimation of vibration
exposure should consider, the actual conditions of use and the
way the tool is used, including taking account of all parts of the
operating cycle such as the times when the tool is switched off
and when it is running idle in addition to the trigger time.
Labels on tool
The following pictograms are shown on the tool:
Warning! To reduce the risk of injury, the user must
read the instruction manual.
Electrical safety
Your charger is double insulated; therefore no
earth wire is required. Always check that the mains
voltage corresponds to the voltage on the rating
plate. Never attempt to replace the charger unit with
a regular mains plug.
If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised Black & Decker Service
Centre in order to avoid a hazard.
Features
This tool includes some or all of the following features.
1. Variable speed switch or two-speed on/off switch
2. Forward/reverse slider
3. Mode selector / torque adjustment collar
4. Chuck
5. Battery
6. Battery release button
Fig. D & E
7. Charger
8. Charging base
9. Charger connector
10. Charger plug
Assembly
Warning! Before assembly, remove the battery from the tool.
Fitting and removing the battery (fi g. A)
To fi t the battery (5), line it up with the receptacle on the
tool. Slide the battery into the receptacle and push until
the battery snaps into place.
To remove the battery, push the two release buttons (6)
simultaneously while at the same time pulling the battery
out of the receptacle.
Fitting and removing a drill bit or
screwdriver bit (fi g. B)
Warning! First remove the battery from the tool.
This tool is fi tted with a keyless chuck to allow for an easy
exchange of bits.
Lock the tool by setting the forward/reverse slider (2) to
the centre position.
Open the chuck by turning the front part (11) with one
hand while holding the rear part (12) with the other (fi g. B).
Insert the bit shank (17) into the chuck.
Firmly tighten the chuck by turning the front part (11) with
one hand while holding the rear part (12) with the other.
Removing and refi tting the chuck (fi g. C)
Open the chuck as far as possible.
Remove the chuck retaining screw by turning it clockwise
using a screwdriver.
Tighten an Allen key (14) into the chuck and strike it with
a hammer as shown.
Remove the Allen key.
Remove the chuck by turning it counterclockwise.
To refi t the chuck, screw it onto the spindle and secure it
with the chuck retaining screw.
Use
Warning! Let the tool work at its own pace. Do not overload.

Charging the battery

The battery needs to be charged before fi rst use and
whenever it fails to produce suffi cient power on jobs that were
easily done before. When charging the battery for the fi rst
time, or after prolonged storage, it will only accept an 80%
charge. After several charge and discharge cycles, the battery
will attain full capacity. The battery may become warm while
charging; this is normal and does not indicate a problem.
Warning! Do not charge the battery at ambient temperatures
below 4 °C or above 40 °C. Recommended charging
temperature: approx. 24 °C.
Charger with charging base (fi g. D)
To charge the battery (5), remove it from the tool and
insert it into the charging base (8). The battery will only fi t
into the charging base in one way. Do not force. Be sure
that the battery is fully seated in the charging base.
Plug in the charger.
After normal use, a charging time of 3 hours will provide
suffi cient power for most applications. However, further
charging for up to 6 hours could signifi cantly increase the use
time, depending on the battery and charging conditions.
Remove the battery from the charger.
Charger without charging base (fi g. E)
To charge the battery, make sure that it is fi tted on the drill.
Insert the charger plug (10) into the connector (9).
Plug in the charger.
Switch on at the mains.
After normal use, a charging time of 3 hours will provide
suffi cient power for most applications. However, further
charging for up to 6 hours could signifi cantly increase the use
time, depending on the battery and charging conditions.
Disconnect the tool from the charger.
Warning! Do not use the tool while it is connected to the charger.
ENGLISH
5