Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
This option does not work in reverse rotation.
To switch the tool off, release the variable speed switch.
u
To switch the tool off when in continuous operation, press
the variable speed switch once more and release it.
Always hold the tool as shown in figure G.
Selecting the direction of rotation (fig. D)
For drilling and tightening screws, use forward (clockwise)
rotation. For loosening screws or removing a jammed drill bit,
use reverse (counterclockwise) rotation.
To select forward rotation, push the forward/reverse slider
u
(3) to the left.
To select reverse rotation, push the forward/reverse slider
u
to the right.
Warning! Never change the direction of rotation while the
motor is running.
Selecting the drilling mode (fig. E)
For Impact drilling in masonry and concrete, set the
u
drilling mode selector (4) to the
For drilling in steel, wood and plastics or for screw driving
u
set the operating mode selector (4) to the
Accessories
The performance of your tool depends on the accessory used.
BLACK+DECKER accessories are engineered to high quality
standards and designed to enhance the performance of your
tool. By using these accessories you will get the very best
from your tool.
Maintenance
Your BLACK+DECKER corded/cordless appliance/tool has
been designed to operate over a long period of time with a
minimum of maintenance. Continuous satisfactory operation
depends upon proper tool care and regular cleaning.
Warning! Before performing any maintenance on corded/
cordless power tools:
Switch off and unplug the appliance/tool.
u
Or switch off and remove the battery from the appliance/
u
tool if the appliance/tool has a separate battery pack.
Or run the battery down completely if it is integral and then
u
switch off.
Unplug the charger before cleaning it. Your charger does
u
not require any maintenance apart from regular cleaning.
Regularly clean the ventilation slots in your appliance/tool/
u
charger using a soft brush or dry cloth.
Regularly clean the motor housing using a damp cloth. Do
u
not use any abrasive or solvent-based cleaner.
Regularly open the chuck and tap it to remove any dust
u
from the interior (when fitted).
Mains plug replacement (U.K. & Ireland only)
If a new mains plug needs to be fitted:
q
position.
r
position.
(Original instructions)
Safely dispose of the old plug.
u
Connect the brown lead to the live terminal in the new
u
plug.
Connect the blue lead to the neutral terminal.
u
Warning! No connection is to be made to the earth terminal.
Follow the fitting instructions supplied with good quality plugs.
Recommended fuse: 5 A.
Protecting the environment
Separate collection. Products and batteries marked
with this symbol must not be disposed of with normal
household waste.
Products and batteries contain materials that can be
recovered or recycled reducing the demand for raw materials.
Please recycle electrical products and batteries according to
local provisions.
Further information is available at www.2helpU.com
Technical data
Rated power
V
AC
No-load speed
min
-1
Impact rate
min
-1
Weight
kg
Max. drilling capacity
Concrete
mm
Steel
mm
Wood
mm
BEH550 Level of sound pressure according to EN 62841:
Sound pressure (L
) 93,5 dB(A), uncertainty (K) 5 dB(A)
pA
Sound power (L
) 104,5 dB(A), uncertainty (K) 5 dB(A)
WA
BEH710 Level of sound pressure according to EN 62841:
Sound pressure (L
) 95,5 dB(A), uncertainty (K) 5 dB(A)
pA
Sound power (L
) 106,5 dB(A), uncertainty (K) 5 dB(A)
WA
BEH550 Vibration total values (triax vector sum) according to EN 62841:
Impact drilling into concrete (a
Drilling into metal (a
h, D
BEH710 Vibration total values (triax vector sum) according to EN 62841:
Impact drilling into concrete (a
Drilling into metal (a
h, D
ENGLISH
BEH550
550
0 ~ 2800
0 ~ 47600
1.7
13
13
25
2
) 14,8 m/s
, uncertainty (K) 1,5 m/s
h, ID
2
2
) 1,8 m/s
, uncertainty (K) 1,5 m/s
2
) 16,2 m/s
, uncertainty (K) 1,5 m/s
h, ID
2
2
) 1,9 m/s
, uncertainty (K) 1,5 m/s
BEH710
710
0 ~ 2800
0 ~ 47600
1.76
13
13
25
2
2
7
Werbung
Inhaltsverzeichnis
