Maintenance; Ec Declaration Of Conformity - Makita 4351T Betriebsanleitung

Guide rail adapter set (accessory)
When cutting parallel and uniform width or cutting
straight, the use of the guide rail and the guide rail
adapter will assure the production of fast and clean cuts.
(Fig. 23)
To install the guide rail adapter, insert the rule bar into the
square hole of the base as far as it goes. Secure the bolt
with the hex wrench securely. (Fig. 24)
Install the guide rail adapter on the rail of the guide rail.
Insert the rule bar into the square hole of the guide rail
adapter. Put the base to the side of the guide rail, and
secure the bolt securely. (Fig. 25)
CAUTION:
• Always use blades No. B-8, B-13, B-16, B-17 or 58
when using the guide rail and the guide rail adapter.
Cover plate (Fig. 26)
Use the cover plate when cutting decorative veneers,
plastics, etc. It protects sensitive or delicate surfaces
from damage. Fit it on the back of the tool base.
Anti-splintering device (Fig. 27)
For splinter-free cuts, the anti-splintering device can be
used. To install the anti-splintering device, move the tool
base all the way forward and fit it from the back of tool
base. When you use the cover plate, install the anti-splin-
tering device onto the cover plate.
CAUTION:
• The anti-splintering device cannot be used when mak-
ing bevel cuts.

MAINTENANCE

CAUTION:
• Always be sure that the tool is switched off and
unplugged before attempting to perform inspection or
maintenance.
To maintain product SAFETY and RELIABILITY, repairs,
carbon brush inspection and replacement, any other
maintenance or adjustment should be performed by Mak-
ita Authorized Service Centers, always using Makita
replacement parts.
ACCESSORIES
CAUTION:
• These accessories or attachments are recommended
for use with your Makita tool specified in this manual.
The use of any other accessories or attachments might
present a risk of injury to persons. Only use accessory
or attachment for its stated purpose.
If you need any assistance for more details regarding
these accessories, ask your local Makita service center.
• Jig saw blades
• Hex wrench 4
• Rip fence (guide rule) set
• Guide rail adapter set
• Guide rail set
• Anti-splintering device
• Dust nozzle
• Cover plate
• Hose (For vacuum cleaner)
For Model 4351T
For European countries only
Noise
The typical A-weighted noise level determined according
to EN60745-2-11:
Sound pressure level (L
Uncertainty (K): 3 dB (A)
The noise level under working may exceed 85 dB (A).
Wear ear protection.
Vibration
The vibration total value (tri-axial vector sum) determined
according to EN60745-2-11:
Work mode: cutting chipboard
Vibration emission (a
Uncertainty (K): 1.5 m/s
Work mode : cutting sheet metal
Vibration emission (a
Uncertainty (K): 1.5 m/s
For Model 4351CT, 4351FCT
For European countries only
Noise
The typical A-weighted noise level determined according
to EN60745-2-11:
Sound pressure level (L
Uncertainty (K): 3 dB (A)
The noise level under working may exceed 85 dB (A).
Wear ear protection.
Vibration
The vibration total value (tri-axial vector sum) determined
according to EN60745-2-11:
Work mode: cutting chipboard
Vibration emission (a
Uncertainty (K): 1.5 m/s
Work mode : cutting sheet metal
Vibration emission (a
Uncertainty (K): 1.5 m/s
EC-DECLARATION OF CONFORMITY
4351T 4351CT, 4351FCT
Model; ,
We declare under our sole responsibility that this product
is in compliance with the following standards of
standardized documents;
EN60745, EN55014, EN61000
in accordance with Council Directives, 2004/108/EC and
98/37/EC.
Tomoyasu Kato
Responsible Manufacturer:
Makita Corporation
3-11-8, Sumiyoshi-cho, Anjo, Aichi, JAPAN
Authorized Representative in Europe:
Makita International Europe Ltd.
Michigan Drive, Tongwell, Milton Keynes,
Bucks MK15 8JD, ENGLAND
): 85 dB (A)
pA
2
): 7 m/s
h,CW
2
2
): 4.5 m/s
h,CM
2
): 85 dB (A)
pA
2
): 6.5 m/s
h,CW
2
2
): 4.5 m/s
h,CM
2
CE 2006
Director
ENH101-7
11