E Zone Settings (Set Zone) - Sanyo VCC-9000EBCP Bedienungsanleitung

AUTOMATIC MODE SETTINGS

E Zone settings (SET ZONE)

1 Select "SET ZONE", and then tilt the
joystick lever to c.
The zone setting screen will be displayed.
Setting a zone number
2
Select "ZONE No.", and then tilt the
joystick lever to c.
The "ZONE No." setting will flash.
·ZONE No.
TITLE: 0000000000000000
SET LEFT LIMIT
SET RIGHT LIMIT
DELETE
DEFAULT SPEED :
RUN
BACK
Tilt the joystick lever to j or l to select
3
the zone number, and then tilt it to d.
Available settings: 001–008
Setting a name
4
Select "TITLE", and then tilt the joystick
lever to c.
The "TITLE" setting will flash.
Enter the zone name.
5
Tilt the joystick lever to j or l to change each
character, and tilt it to d or c to move the flashing
cursor to a different position.
Tilt the joystick lever to d and hold it there until
displayed. This completes the setting.
Available settings: 0–9, A–Z, a–z, blank
6 Setting the left edge
1
Select "SET LEFT LIMIT", and then tilt the joystick
lever to c.
The "CALL PRESET 1 TO CONFIRM ......" screen will
be displayed.
ZONE No. : 001
TITLE: 0000000000000000
·SET LEFT LIMIT
SET RIGHT LIMIT
DELETE
DEFAULT SPEED : 001
CALL PRESET 1 TO
CONFIRM......
2
Tilt the joystick lever to the left to confirm.
3
After making the setting, press the "1" numeric
button, and then press the ENTER button.
Setting the right edge
7
1
Select "SET RIGHT LIMIT", and then tilt the
joystick lever to c.
: 001
001
·
is
1
ENTER
The "CALL PRESET 1 TO CONFIRM ......" screen will
be displayed.
ZONE No.
TITLE: 0000000000000000
SET LEFT LIMIT
·SET RIGHT LIMIT
DELETE
DEFAULT SPEED :
CALL PRESET 1 TO
CONFIRM......
2
Tilt the joystick lever to the right to confirm.
3
After making the setting, press the "1" numeric
button, and then press the ENTER button.
8 Setting the zone mode speed
Select "RUN" and then set the speed that is to be used
only when using the zone mode.
1
Select "DEFAULT SPEED", and then tilt the
joystick lever to c.
The "DEFAULT SPEED" setting will flash.
2
Tilt the joystick lever to j or l to set the value,
and then tilt it to d.
Available settings:
Select "BACK", and then tilt the joystick
9
lever to c to complete the setting.
Starting a zone mode
1 Select "SET ZONE", and then tilt the
joystick lever to c.
The zone setting screen will be displayed.
Select "ZONE No.", and then tilt the
2
joystick lever to c.
The "ZONE No." setting will flash.
Tilt the joystick lever to j or l to select a
3
zone number to be started, and then tilt it
to d.
4 Select "RUN", and then tilt the joystick
lever to c.
ZONE
TITLE: 0000000000000000
SET LEFT LIMIT
SET RIGHT LIMIT
DELETE
DEFAULT SPEED :
·RUN
BACK
The selected zone mode will start.
To stop the zone mode, use the joystick lever of the
system controller.
NOTE: If you create a new zone area that overlaps an
existing zone area, the new area will have priority
when the overlapped section is monitored.
5 Select "BACK", and then tilt the joystick
lever to c to complete the setting.
- 38 -
: 001
001
1
(slow) – seconds (fast)
ƒ ƒ „ … ˆ ˆ
No. : 001
001
ENTER
English