Specifications - Makita 9561CR Bedienungsanleitung

ENGLISH
1-1. Shaft lock
2-1. Slide switch
3-1. Indication lamp (speed adjusting
dial)
4-1. Indication lamp
5-1. Speed adjusting dial
7-1. Wheel guard
7-2. Bearing box
7-3. Screw
8-1. Wheel guard
8-2. Bearing box

SPECIFICATIONS

Depressed center wheel
diameter Spindle thread
Rated speed (n) / No load speed (
• Due to our continuing programme of research and development, the specifications herein are subject to change without notice.
• Note: Specifications may differ from country to country.
Intended use
The tool is intended for grinding, sanding and cutting of
metal and stone materials without the use of water.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and
can only be operated on single-phase AC supply. They
are double-insulated in accordance with European
Standard and can, therefore, also be used from sockets
without earth wire.
For Model 9561CR,9561CVR,9562CR,9562CVR
For European countries only
Noise
The typical A-weighted noise level determined according
to EN60745-2-3:
Sound pressure level (L
Uncertainty (K) : 3 dB(A)
The noise level under working may exceed 85 dB (A).
Wear ear protection.
Vibration
The vibration total
determined according to EN60745-2-3:
Work mode : surface grinding
Vibration emission (a
Uncertainty (K) : 1.5 m/s
Cutting-off or wire brushing may have different vibration
Explanation of general view
8-3. Screw
8-4. Lever
9-1. Screw
10-1. Lock nut
10-2. Depressed center grinding wheel /
Multi-disc
10-3. Inner flange
11-1. Lock nut wrench
11-2. Shaft lock
12-1. Lock nut
12-2. Diamond wheel
115 mm M14
125 mm M14
n
)
o
Overall length
Net weight
Safety class
) : 83 dB(A)
pA
value (tri-axial vector
2
) : 8.5 m/s
h,AG
2
9561CR
9562CR
11,000
-1
(min )
289 mm
1.8 kg
ENE048-1
emission values.
For Model 9564CR,9564CVR
ENF002-1
For European countries only
Noise
The typical A-weighted noise level determined according
to EN60745-2-3:
Sound pressure level (L
Uncertainty (K) : 3 dB(A)
The noise level under working may exceed 85 dB (A).
Vibration
ENG101-1
The vibration
determined according to EN60745-2-3:
Work mode : surface grinding
Vibration emission (a
Uncertainty (K) : 1.5 m/s
Cutting-off or wire brushing may have different vibration
emission values.
ENG208-2
For Model 9565CR,9565CVR
sum)
For European countries only
Noise
The typical A-weighted noise level determined according
to EN60745-2-3:
Sound pressure level (L
4
12-3. Inner flange
12-4. Spindle
13-1. Marking A
14-1. Marking B
15-1. Marking C
16-1. Pin
16-2. Vent
18-1. Exhaust vent
18-2. Inhalation vent
9564CR 9561CVR
9565CR 9562CVR
11,000 2,800 - 11,000
-1 -1
(min ) (min )
299 mm 289 mm
1.8 kg 1.8 kg
/II
) : 83 dB(A)
pA
Wear ear protection.
total value (tri-axial
) : 8.0 m/s
h,AG
2
) : 82 dB(A)
pA
9564CVR
9565CVR
2,800 - 11,000
-1
(min )
299 mm
1.8 kg
ENG101-1
ENG208-2
vector sum)
2
ENG101-1