Troubleshooting; Declaration Of Conformity - STEINEL sensIQ S Bedienungsanleitung

Troubleshooting

Malfunction Cause
■ Fuse has blown; not
Sensor without power
switched ON; break in wiring
■ Short circuit
■ Twilight setting in night-time
Sensor will not switch ON
mode during daytime
operation
■ Bulb faulty
■ Mains power switch OFF
■ Fuse faulty
■ Detection zone not correctly
adjusted
■ Continued movement within
Sensor will not switch OFF
the detection zone
■ Light is in detection zone
and keeps switching ON
as a result of temperature
change
■ Light being operated is in
the manual override mode
(LED ON)
■ Light being operated in the
Sensor keeps switching
ON/OFF
detection zone
■ Animals moving in detection
zone
■ Wind is moving trees and
Sensor responds when it
should not
bushes in the detection
zone
■ Cars in the street are
detected
■ Sunlight is shining on the
lens
■ Sudden temperature
changes due to weather
(wind, rain, snow) or air
expelled from fans, open
windows
■ Differing ambient
Change in sensor's reach
temperatures
■ Remote control not
Detector not responding
to remote control
programmed
Remedy
■ New fuse, turn on power
switch, check wiring with
voltage tester
■ Check connections
■ Adjust setting
■ Change bulb
■ Switch ON
■ Replace fuse, check
connection if necessary
■ Re-adjust
■ Check zone and readjust if
necessary or fit shrouds
■ Adjust detection zone or fit
shrouds
■ Deactivate manual override
■ Adjust detection zone or fit
shrouds, increase distance
■ adjust zone, or apply
shrouds
■ Change zone
■ Change zone
■ Mount sensor in a protected
place or change zone
■ Adjust detection zone or
install in a different place
■ Adjust reach by reach
controller , if necessary
applying film shrouds
■ Disconnect sensor from the
power supply for approx.
5 sec. Switch on the voltage
again and press the button
on the remote control within
10 min.
- 16 -
Operation/Maintenance
The infrared sensor can be used for switching
light ON and OFF automatically. The unit is not
suitable for burglar alarm systems as it is not
tamperproof in the manner prescribed for such
systems. Weather conditions may affect the
way the motion detector works. Strong gusts
of wind, snow, rain or hail may cause the light
Accessories
Corner wall mount:
Black: 4007841 608828
White: 4007841 608835
Stainless steel: 4007841 608804

Declaration of conformity

This product complies with
- Low-Voltage Directive 2006/95/EC
- EMC Directive 2004/108/EC
- RoHS Directive 2011/65/EC
- WEEE Directive 2002/96/EC
Functional Warranty
This Steinel product has been manufactured
with the utmost care, tested for proper opera-
tion and safety in accordance with applicable
regulations and then subjected to random
sample inspection. Steinel guarantees that it is
in perfect condition and proper working order.
The warranty period is 36 months and starts
on the date of sale to the consumer. We will
remedy defects caused by material flaws or
manufacturing faults. The warranty will be met
by repair or replacement of defective parts at
our own discretion. The warranty does not
cover damage to wear parts, nor does it cover
damage or defects caused by improper treat-
ment, maintenance or the use on non-genuine
parts. Further consequential damage to other
objects shall be excluded.
SENSOR
to come ON when it is not wanted because
the sensor is unable to distinguish sudden
changes of temperature from sources of heat.
The detector lens may be cleaned with a damp
cloth if it gets dirty (do not use cleaning
agents).
Claims under the warranty will only be
accepted if the light is sent fully assembled
and well-packed with a brief description of
the fault, a receipt or invoice (date of purchase
and dealer's stamp) to the appropriate Service
Centre.
Repair service:
If defects occur outside the
warranty period or are not
covered by warranty, ask
your nearest service station
for the possibility of repair.
- 17 -