Specifications - Makita BO4900V Bedienungsanleitung

ENGLISH (Original instructions)
1-1. Speed adjusting dial
1-2. Lock button
1-3. Switch trigger
2-1. Clamp lever
2-2. Conventional type of abrasive paper
with pre-punched holes
2-3. Pad for conventional type of
abrasive paper
3-1. Punch plate
3-2. Conventional type of abrasive paper
without pre-punched holes

SPECIFICATIONS

Abrasive paper size
Orbits per minute (min
Sanding stroke rate (min
• Due to our continuing programme of research and development, the specifications herein are subject to change without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
Intended use
The tool is intended for the sanding of large surface of
wood, plastic and metal materials as well as painted
surfaces.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated in accordance with European Standard
and can, therefore, also be used from sockets without
earth wire.
Noise
The typical A-weighted noise level determined according
to EN60745:
Sound pressure level (L
Uncertainty (K) : 3 dB(A)
The noise level under working may exceed 80 dB (A).
Wear ear protection
Vibration
The vibration total value (tri-axial vector sum) determined
according to EN60745:
Explanation of general view
4-1. Hook-and-loop type of abrasive
paper with pre-punched holes
4-2. Pad for hook-and-loop type of
abrasive paper
5-1. Pad
5-2. Screws
5-3. Screwdriver
6-1. Groove
6-2. Front fixing cardboard
6-3. Paper dust bag
7-1. Claws
Model
Pad size
-1
)
-1
)
Overall length
Net weight
Safety class
) : 71 dB(A)
pA
BO4900V
115 mm x 229 mm
115 mm x 280 mm
4,000 - 10,000
8,000 - 20,000
289 mm
2.7 kg
ENE052-1
Model BO4900,BO4900V
Work mode : sanding metal plate
Vibration emission (a
Uncertainty (K) : 1.5 m/s
ENF002-1
Model BO4901
Work mode : sanding metal plate
Vibration emission (a
Uncertainty (K) : 1.5 m/s
The declared vibration emission value has been
•
ENG905-1
measured in accordance with the standard test
method and may be used for comparing one tool
with another.
The declared vibration emission value may also be
•
used in a preliminary assessment of exposure.
WARNING:
The vibration emission during actual use of the
•
power tool can differ from the declared emission
value depending on the ways in which the tool is
ENG900-1
used.
Be sure to identify safety measures to protect the
•
operator that are based on an estimation of
exposure in the actual conditions of use (taking
account of all parts of the operating cycle such as
3
7-2. Upper part
8-1. Guide
8-2. Notch
11-1. Push button
12-1. Dust nozzle
12-2. Hook
12-3. Dust bag
12-4. Push button
BO4900
115 mm x 229 mm 115 mm x 229 mm
115 mm x 280 mm 115 mm x 280 mm
10,000
20,000
289 mm
2.7 kg
/II
2
) : 2.5 m/s or less
h
2
2
) : 4.0 m/s
h
2
BO4901
10,000
20,000
289 mm
2.7 kg
ENG901-1