Aux Operations; Trouble Shooting - Clarion CZ702E Benutzerhandbuch & Installationshandbuch

Bluetooth Operations
Track-down
1. Press the [ ] button to move to the
beginning of the previous track.
2. Each time the [ ] button is pressed,
playback proceeds to previous track in the
reverse direction.
Note:
Playing order will depend on Bluetooth audio
player. When [ ] button is pressed, some
A2DP devices will restart the current track
depends on the duration of playback.
During music streaming playback, "A2DP
and HFP" will be shown on the display. When
A2DP device is disconnected,
"BLUETOOTH DISCONNECT" will be shown
on the display and return to previously
selected audio source. Some Bluetooth
audio players may not have play / pause
synchronized with this unit. Please make sure
both device and main unit are in the same
play / pause status in BT MUSIC mode.

AUX Operations

Press [SRC / ] button on the panel to select
"AUX".
AUX is just for audio content with 3.5mm Jack
connector plugged into audio-in socket on the
front panel.
AUX Input sensitivity setting
1. Press and hold the [DISP] button (1 sec.).
2. Turn the [VOLUME] knob to select "AUX
SENS".
3. If the output level of connected external
audio player is "HIGH", rotate [VOLUME]
knob and choose "LOW". And if the output
level is "LOW", choose "HIGH".
14
CZ702E
ID3 display
During music streaming playback, for music
information that is longer than the display
panel:
When SCROLL is ON, the LCD will display
ID3 TAG information cyclely, e.g: ALBUM-
>TITLE->ARTIST>...
When SCROLL is OFF, the LCD will display
one of the ID3 TAG information, the default
is TRACK, but user can adjust it to other ID3
TAG information by press [ DISP ] button.

6. TROUBLE SHOOTING

GENERAL
Problem Cause
Unit fuse blown.
Unit can not
power on.
Car battery fuse blown.
Unit can not
power on.
Nothing happens
when buttons are The microprocessor has
pressed. malfunctioned due to noise, etc.
Display is not
accurate.
Improper audio output connection. Check wiring and correct.
Volume set too low.
No/low audio Speakers damaged.
output.
Heavily biased volume balance.
Speaker wiring is in contact with
metal part of car.
Non-standard disc used.
Speaker power rating does not
Poor sound quality
match unit.
or distortion.
Wrong connections.
Speaker is shorted.
Tel-Mute
MUTE wire is grounded.
malfunction
Unit resets itself Incorrect connection between ACC
when engine is off. and Battery.
DISC Player
Problem Cause
Another disc is already loaded.
Disc cannot be
There is an object installed inside the
loaded.
unit.
Compact disc is dirty.
Sound skips or is
Compact disc is heavily scratched or
noisy.
warped.
Sound is bad when Condensation may form on the internal
power is first turned lens when the car is parked in a humid
on. place.
Measure
Replace with new fuse of correct rating.
Replace with new fuse of correct rating.
Turn off the power and remove the DCP.
Press the [RESET] button with a thin rod.
Note:
When the [RESET] button is pressed, turn off
the ACC power.*
* When the [RESET] button is pressed,
preset radio stations, titles, etc. stored in
memory are kept.
Increase volume level.
Replace speakers.
Adjust the channel balance to center position.
Insulate all speaker wiring connections.
Use a standard disc.
Replace speakers.
Check wiring and correct.
Check wiring and correct.
Check the MUTE wiring and correct.
Check wiring and correct.
Measure
Eject the disc before loading the new one.
Remove the object inside the unit.
Clean the compact disc with a soft cloth.
Replace with a compact disc with no
scratches.
Let dry for about 1 hour with power on.