Radio Data System Operations; Dab Operations - Clarion CZ702E Benutzerhandbuch & Installationshandbuch

Radio Data System Operations

Radio Data System
This unit has a built-in "Radio Data System"
decoder system that supports broadcast
stations transmitting "Radio Data System" data.
When using the "Radio Data System" function,
always set the radio to FM mode.
AF function
The AF function switches to a different
frequency on the same network in order to
maintain optimum reception.
* The factory default setting is ON.
1. Set to system setup by long pressing [DISP]
button.
2. Press the [ ] or [ ] button to select
"AF".
3. Rotate the [VOLUME] knob to select ON or
off.
• AF ON:
"AF" indicator appears in the display and AF
function turns on.
• AF OFF:
"AF" indicator disappears in the display and
Af function turns off.
REG (Regional programme) function
When the REG function is ON, the optimum
regional station can be received. When this
function is OFF, if the regional station area
switches as you drive, a regional station for
that region is received.
* The factory default setting is ON.
Notes:
• This function is disabled when a national
station such as BBC R2 is being received.
• The REG function ON/OFF setting is valid
when the AF function is ON.
1. Set to system setup by long pressing [DISP]
button.
2. Press the [ ] or [ ] button to select
"REG".
3. Rotate the [VOLUME] knob to select ON or
off.
Manually tuning a regional station
in the same network
This function is valid when the AF function is
ON and the REG function is OFF.
10
CZ702E
Manually tuning a regional station in
the same network
This function is valid when the AF function is
ON and the REG function is OFF.
Note:
This function can be used when a regional
broadcast of the same network is received.
TA (Traffic Announcement)
In the TA standby mode, when a traffic
announcement broadcast starts, the traffic
announcement broadcast is received as top
priority regardless of the function mode so you
can listen to it. Traffic programme (TP)
automatic tuning is also available.
* This function can only be used when "TP"
appears in the display. When "TP" appears, this
means that the "Radio Data System" broadcast
station being received has traffic announcement
programmes.
Setting the TA standby mode
If you press the [TA] button, "TA" lights in the
display and the unit is set into the TA standby
mode until a traffic announcement is broadcast.
When a traffic announcement broadcast starts,
"TRAF INF" appears in the display. If you press
the [TA] button while a traffic announcement
b r o a d c a s t i s b e i n g r e c e i v e d , t h e t r a f f i c
announcement broadcast reception is cancelled
and the unit goes into the TA standby mode.
Cancelling the TA standby mode
As "TA" lights in the display, press the [TA]
button. The "TA" in the display goes off and the
TA standby mode is cancelled.
PTY (Programme Type)
This function enables you to listen to a
broadcast of the selected programme type even
if the unit is on a function mode other than radio.
* Some countries do not yet have PTY
broadcast.
* In the TA standby mode, a TP station has
priority over a PTY broadcast station.
Selecting PTY
Press [MENU / ] button, then rotate the
[VOLUME] knob to select PTY type, press the
[VOLUME] knob, the unit begin searching.

DAB Operations

This function is available when DAB302E
(sold separately) is connected.
Select tuner as playing source
Press [SRC / ] button once or more to
enter DAB mode.
Selecting the radio band
Press the [BAND / ] button on the panel
or on the remote control to select one radio
band among D1, D2 and D3.
Selecting the ensemble
• Manual selecting
During manual selecting, the ensemble
will be changed in steps.
Press the [ ] or [ ] button on
the panel to tune in a higher / lower
ensemble.
• Auto selecting
Press and hold the [ ] or [ ]
button to seek a higher / lower ensemble.
To stop searching, repeat the operation
above or press other buttons having radio
functions.
Note:
When a ensamble service is received,
searching stops and the service in current
ensemble is played.
Turning the service
• Manual turning
During manual turning, the ensemble will
be changed in steps.
Press the [ ] or [ ] button on the
panel to tune in a higher / lower service.
• Auto turning
Press and hold the [ ] or [ ]
button to seek a higher / lower service.
To stop searching, repeat the operation
above or press other buttons having radio
functions.
Note:
When a service is received, searching stops
and the service is played.
Manual store
When one expected service has been
detected, press and hold button [ 1-6 ] to store
it in the memory.
Preset scan
Preset scan receives the services stored
in preset memory in order. This function is
useful when searching for a desired service
in memory.
1. Press the [PS/AS] button.
2. When a desired service is tuned in, press
the [PS/AS] button again to continue
receiving that service.
Recall the stored stations
Press one numeric button among 1 to 6 on
the panel to select the corresponding stored
service.
REG (Regional programme)
TA (Traffic Announcement)
PTY (Programme Type)
These functions is same as Radio Data
system. Refer to page10.