Timex METROPOLITAN+ Benutzerhandbuch Seite 3

return completely to the zero position at midnight, and can become further
out of calibration until the battery is replaced. To further save the battery
power until it is replaced the INDIGLO
battery has been replaced. The activity tracking function will remain active
until the battery has been completely depleted, but new data will not
be stored.
BATTERY REPLACEMENT
Before replacing the battery, it is recommended that you synchronize
to the phone to make sure you have retrieved all of the latest activity
data from the watch. After the battery has been replaced, the watch will
automatically calibrate the sub-dial hands. Upon completion of the auto-
calibration process, the upper sub-dial hand will point to "OFF" and the
lower sub-dial hand will be positioned at ZERO. The activity tracking function
will be off. You will need to adjust the center hand and synchronize the
watch with the Smartphone application. Open the Timex Connected app on
your phone. Press and hold button A. The upper sub-dial hand will move
to the Bluetooth symbol. Perform the synchronization of the watch and
®
Smartphone application. Once the watch has been synchronized with the
Smartphone, the activity tracking function can be activated.
STORING THE WATCH
The power may be removed from the watch for storage. Pull the crown out to
the outer position. The hour, minute and second hands will immediately stop
and the activity tracking function will be completely inactive after 30 minutes
with the crown in this position.
FIRMWARE UPDATE
As updates for the Smartphone application are published you will receive
notification through your Smartphone application. The firmware update will
delete all activity recorded for the current day, therefore it is recommended
the update be done early in the day to minimize the loss of recorded
activity. The length of time for the synchronization varies from iOS to Android
platforms and the various devices within each platform. The average length
of time for the synchronization is 5 to 10 minutes, but in extreme cases
could take as many as 30 minutes. During the synchronization you should
place the watch and the smartphone on a flat surface next to each other, not
moving them until the synchronization process is complete. While the update
via synchronization is occurring the lower sub-dial hand will indicate the
progress of the download, moving from 0 to 100%.
STRIDE LENGTH ADJUSTMENT
The Timex Metropolitan+ uses an algorithm for distance measurement which
automatically determines your stride, based on your height and speed. If you
find the distance reported does not match your actual walking or running
distance you can calibrate the distance by up to +/- 25% via the Smartphone
application. This is done by the distance adjustment option on the watch
section of the application.
WATER RESISTANCE
WARNING: TO MAINTAIN WATER RESISTANCE, DO NOT PRESS ANY
BUTTONS UNDER WATER.
1. Watch is water-resistant only as long as lens, push buttons and case
remain intact.
2. Watch is not a diver watch and should not be used for diving.
3. Rinse watch with fresh water after exposure to salt water.
If your watch is water-resistant, meter marking or (O) is indicated.
Water-Resistance Depth
30m/98ft
50m/164ft
100m/328ft
200 m/656ft
* pounds per square inch absolute.
1 ATM = 10m / 32.8ft
©2015 Timex Group USA, Inc. TIMEX, TRUE SINCE 1854 TIMEX and INDIGLO are
registered trademarks of Timex Group B.V. and its subsidiaries. The Bluetooth word mark
and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such
marks by Timex is under license.
night-light will not function until the
®
p.s.i.a. * Water Pressure Below Surface
60
86
160
284
FCC NOTICE (U.S.) / IC NOTICE (CANADA):
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not
cause interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables
aux appareils radio exempts de licence. L'exploitation est autorisée aux deux
conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2)
l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d'en compromettre le
fonctionnement.
Under Industry Canada regulations, this radio transmitter may only operate
using an antenna of a type and maximum (or lesser) gain approved for the
transmitter by Industry Canada.
To reduce potential radio interference to other users, the antenna type and
its gain should be so chosen that the equivalent isotropically radiated power
(e.i.r.p.) is not more than that necessary for successful communication.
Conformément à la réglementation d'Industrie Canada, le présent émetteur
radio peut fonctionner avec une antenne d'un type et d'un gain maximal
(ou inférieur) approuvé pour l'émetteur par Industrie Canada.
Dans le but de réduire les risques de brouillage radioélectrique à l'intention
des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte
que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas
l'intensité nécessaire à l'établissement d'une communication satisfaisante.
NOTE: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
— Consult the dealer or an experienced radio TV technician for help.
DECLARATION OF CONFORMITY
Timex Group USA, Inc.
Manufacturers Name:
Manufacturers Address: 555 Christian Road
Middlebury, CT 06762
United States of America
declares that the product:
Product Name: Timex
M372
Model Numbers:
conforms to the following specifications:
R&TTE: 1999/05/EC
CENELEC EN 55022
Standards:
ETSI EN 301 489-1
ETSI EN 301 489-3
ETSI EN 301 489-17
ETSI EN 300 440-2
LVD: 2006/95/EC
Standards: IEC 60950-1
CENELEC EN 60950-1
Digital Device Emissions
Standards: FCC 47CFR 15C Part 15 Subpart C 15.247 (Bluetooth)
FCC 47CFR 15B clA Part 15 Subpart B Unintentional
Radiators
FCC 47CFR 15B clA Part 15 Subpart C 15.247 (Bluetooth)
IC RSS 210 Issued:2010/12/01
ICES 003
SAI AS/NZS 4268
Agent:
Sam Everett
Quality Regulatory Engineer
Date: 11 July, 2015, Middlebury, Connecticut, U.S.A.
3
ENGLISH 032-095000-02
Register your product at www.timex.com
Metropolitan+
®
REVISED 12.4.15