Description Of The Hood; Operation - Elica Tender Serie Gebrauchsanweisung

10. Connect a pipe (pipe and pipe clamps not provided, to be
purchased separately) for discharge of fumes to the
connection ring located over the suction motor unit.
If the hood is to be used in ducting version, the other end
of the pipe must be connected to a device expelling the
fumes to the outside. If the hood is to be used in filter
version, then fix the deflector F to the chimney support
bracket G and connect the other extremity of the pipe to
the connection ring placed on the deflector F.
11. Connect the electricity.
12. Apply the chimney stacks and fasten them at the top to
the chimney support „G" (12b) using 2 screws (12a)
13. Slide the bottom section of the chimney down until it
completely covers the suction unit and slots into the
housing provided on top of the hood.
Remount the carbon filter frame and the fat/s filter/s and check
the perfect functioning of the hood.

Description of the hood

Fig. 1
1. Control panel
2. Grease filter
3. Grease filter release handle
4. Halogen lamp
5. Vapour catcher
6. Telescopic chimney
7. Air outlet (used for filter version only)

Operation

Use the high suction speed in cases of concentrated kitchen
vapours. It is recommended that the cooker hood suction is
switched on for 5 minutes prior to cooking and to leave in
operation during cooking and for another 15 minutes
approximately after terminating cooking.
Control panel
1. Light Button
• Press lamp button to turn ON the light on High
Intensity (Lamp state previously OFF).
• Press lamp button to turn ON the light on Low
Intensity (Lamp state previously ON).
• Press lamp button to turn OFF the light (Lamp state
previously ON).
2. Timer Button
• The default timer setting is 10 minutes, and it can be
adjusted between 60 minutes and 1 minute.
• After pressing the timer button, the control enters to
a timer setup mode, and user can adjust the timer
countdown time with the "+" and "-" buttons within 5
seconds. The timer can be initiated immediately
pressing the timer button, after setting the timer
duration or pressing the timer button twice (default
10 minutes setting).
• If no action occurs within 5 seconds, the countdown
will start.
• During the timer setup the "+" and "-" buttons are
dedicated to the timer and no motor action will
occur.
• Once the timer is initiated, it can be cancelled by
pressing the timer button again.
3. Display
• Shows the hood settings.
• The display will be lit at low intensity when the hood
is not operating.
Pressing any key the display will light up at high
intensity.
• The display will be lit at high intensity when the hood
is operating.
If no key is pressed within a minute the display will
return to being lit at low intensity.
4. "-" Button. Speed Decrease / OFF
• This button is used to decrease the fan speed, or
turn OFF the fan.
• The fan will turn OFF if the "-" button is pressed and
the hood was in the first speed.
• If the fan is at second speed and the "-" button is
pressed, the fan will be set to first speed.
• If the fan is at third speed and the "-" key is pressed,
the fan will be set to second speed.
• If the fan is at fourth speed and the "-" button is
pressed, the fan will be set to third speed.
• If the fan is OFF and the "-" button is pressed, the
control backlight will light up.
5. "+" Button. Speed Increase / ON
• This button is used to increase the fan speed, or
turn ON the fan.
• The fan will turn ON if the "+" button is pressed and
the hood was OFF.
• If the fan is at first speed and the "+" button is
pressed, the fan will be set to second speed.
• If the fan is at second speed and the "+" button is
pressed, the fan will be set to third speed.
• If the fan is at third speed and the "+" button is
pressed, the fan will be set to fourth speed.
• If the fan is at fourth speed and the "+" button is
pressed, a beep will sound.
11