Output System Installation; Intake System Installation - Fluval Roma LED Gebrauchsanleitung

rings (C). Do not proceed with the installation if one of the rubber
rings (C) is missing but contact your local supplier.
Before proceeding, check stems (A) for the presence of all 3 rubber rings (C). Do not proceed with the
installation if one of the rubber rings (C) is missing but contact your local supplier.
Locate the 2 openings in the tank bottom glass and assure that the cor-
Locate the 2 openings in the tank bottom glass and assure that
the corresponding openings in the cabinet are aligned with them.
The 2 openings in the tank bottom glass are complete with factory-
installed special plastic fittings, which must never be removed,
Locate the 2 openings in the tank bottom glass and assure that
turned or loosened and with two sealing plugs (P) and (Q).
the corresponding openings in the cabinet are aligned with them.
The output system should be installed in the opening (O), whereas
The 2 openings in the tank bottom glass are complete with factory-
Connector Stem's
the intake should be installed in the opening (I).
installed special plastic fittings, which must never be removed,
Rubber Rings (C)
turned or loosened and with two sealing plugs (P) and (Q).
The output system should be installed in the opening (O), whereas
the intake should be installed in the opening (I).
responding openings in the cabinet are aligned with them. The 2 open-
ings in the tank bottom glass are complete with factory installed special
plastic fittings, which must never be removed, turned or loosened and with two sealing plugs (P) and (Q). The
output system should be installed in the opening (O), whereas the intake should be installed in the opening (I).
Once the output/input systems are installed, do not shift the tank with respect to the cabinet as this may
damage the output/input systems and the glass tank.
Do not force, loosen or turn the factory-installed special fittings on tank openings (I) and (O).

Output system installation

Output system installation
1. Manually unscrew plug (P) and remove plug (Q) from opening (O) (Pict.1).
Important: keep plugs (P) & (Q) for any future use.
1. Manually unscrew plug (P) and remove plug (Q) from opening (O) (Pict.1). Important: keep
Output system installation
2. Slip connector stem (A) fully through opening (O) until it stops (Pict.2)
plugs (P) & (Q) for any future use. 1. Manually unscrew plug (P) and remove plug (Q) from opening (O) (Pict.1).
3. Open the cabinet. Screw and tighten the ring nut (R) onto the bottom end of
stem (A) (Pict. 3).
2. Slip connector stem (A) fully through opening (O) until it stops (Pict.2).
2. Slip connector stem (A) fully through opening (O) until it stops (Pict.2)
4. Insert the outlet nozzle (N) into one end of outlet stem (B)
3. Open the cabinet. Screw and tighten the ring nut (R) onto the bottom end of stem (A) (Pict. 3).
3. Open the cabinet. Screw and tighten the ring nut (R) onto the bottom end of
5. Insert outlet stem (B) onto connector stem (A) (Pict.4).
4. Insert the ouput nozzle (N) into one end of output stem (B).
6. Regulate the height of outlet nozzles according to your requirement by sliding outlet
4. Insert the outlet nozzle (N) into one end of outlet stem (B)
5. Insert output stem (B) onto connector stem (A) (Pict.4).
stem (B) along connector stem (A).
5. Insert outlet stem (B) onto connector stem (A) (Pict.4).
7. The outlet nozzles (N) can be easily rotated to divert the water flow where desired.
6. Regulate the height of outlet nozzles according to your requirement by sliding outlet stem
6. Regulate the height of outlet nozzles according to your requirement by sliding outlet
(B) along connector stem (A).
7. The outlet nozzles (N) can be easily rotated to divert the water flow where desired.
7. The outlet nozzles (N) can be easily rotated to divert the water flow where desired.
Direct water jets so as not to let water overflow from the tank. Avoid directing the water jets against the

Intake system installation

LED Strip-Light(s)
1. Manually unscrew plug (P) and remove plug (Q) from opening (I) (Pict.1).
Important: keep plugs (P) & (Q) for any future use.
Intake system installation
2. Slip the second connector stem (A) fully through opening (I) until it stops (Pict.2).
Intake system installation
1. Manually unscrew plug (P) and remove plug (Q) from opening (I) (Pict.1).
3. Open the cabinet. Screw and tighten the nut ring (R) onto the bottom end of the
second stem (A) (Pict.3).
1. Manually unscrew plug (P) and remove plug (Q) from opening (I) (Pict.1). Important: keep
2. Slip the second connector stem (A) fully through opening (I) until it stops (Pict.2).
4. Insert the intake strainer (S) onto connector stem (A) (Pict.5).
plugs (P) & (Q) for any future use. 3. Open the cabinet. Screw and tighten the nut ring (R) onto the bottom end of the
2. Slip the second connector stem (A) fully through opening (I) until it stops (Pict.2).
4. Insert the intake strainer (S) onto connector stem (A) (Pict.5).
3. Open the cabinet. Screw and tighten the nut ring (R) onto the bottom end of the second
stem (A) (Pict.3).
4. Insert the intake strainer (S) onto connector stem (A) (Pict.5).
If in the event a different filtration system is used, which does not require the inlet/outlet systems supplied with
this unit (e.g. an internal filter), restore the initial conditions by removing the 2 connector stems (A) and closing
openings (O) and (I) with plugs (P) & (Q). Plug (Q) ensures a watertight seal and has to be inserted into its seat
If in the event a different filtration system is used, which does not require the inlet/outlet systems supplied with
by pressing it. Plug (P) is designed to protect plug (Q) and ensure that plug (Q) remains in its seat properly. Screw
this unit (e.g. an internal filter), restore the initial conditions by removing the 2 connector stems (A) and closing
plug (P) by hand only until it will go without forcing it. DO NOT USE ANY TOOLS, AS DOING SO MAY DAMAGE
openings (O) and (I) with plugs (P) & (Q). Plug (Q) ensures a watertight seal and has to be inserted into its seat
THE UNIT.
by pressing it. Plug (P) is designed to protect plug (Q) and ensure that plug (Q) remains in its seat properly. Screw
plug (P) by hand only until it will go without forcing it. DO NOT USE ANY TOOLS, AS DOING SO MAY DAMAGE
THE UNIT.
Ring Nut Ring Nut
(R)
(R)
Pict. 3
Pict. 3
Locate the 2 openings in the tank bottom glass and assure that
the corresponding openings in the cabinet are aligned with them.
The 2 openings in the tank bottom glass are complete with factory-
installed special plastic fittings, which must never be removed,
turned or loosened and with two sealing plugs (P) and (Q).
The output system should be installed in the opening (O), whereas
the intake should be installed in the opening (I).
Once the output/input systems are installed, do not shift the
tank with respect to the cabinet as this may damage the
output/input systems and the glass tank.
Do not force, loosen or turn the factory-installed special
fittings on tank openings (I) and (O).
Once the output/input systems are installed, do not shift the
tank with respect to the cabinet as this may damage the
output/input systems and the glass tank.
9
Once the output/input systems are installed, do not shift the
Do not force, loosen or turn the factory-installed special
tank with respect to the cabinet as this may damage the
fittings on tank openings (I) and (O).
output/input systems and the glass tank.
Output system installation
1. Manually unscrew plug (P) and remove plug (Q) from opening (O) (Pict.1).
Do not force, loosen or turn the factory-installed special
Important: keep plugs (P) & (Q) for any future use.
fittings on tank openings (I) and (O).
2. Slip connector stem (A) fully through opening (O) until it stops (Pict.2)
3. Open the cabinet. Screw and tighten the ring nut (R) onto the bottom end of
stem (A) (Pict. 3).
4. Insert the outlet nozzle (N) into one end of outlet stem (B)
5. Insert outlet stem (B) onto connector stem (A) (Pict.4).
6. Regulate the height of outlet nozzles according to your requirement by sliding outlet
stem (B) along connector stem (A).
7. The outlet nozzles (N) can be easily rotated to divert the water flow where desired.
Direct water jets so as not to let water overflow from the tank.
Avoid directing the water jets against the Strip-Light(s) of the canopy
Important: keep plugs (P) & (Q) for any future use.
Intake system installation
stem (A) (Pict. 3).
1. Manually unscrew plug (P) and remove plug (Q) from opening (I) (Pict.1).
Important: keep plugs (P) & (Q) for any future use.
2. Slip the second connector stem (A) fully through opening (I) until it stops (Pict.2).
Direct water jets so as not to let water overflow from the tank.
stem (B) along connector stem (A).
3. Open the cabinet. Screw and tighten the nut ring (R) onto the bottom end of the
Avoid directing the water jets against the Strip-Light(s) of the canopy
second stem (A) (Pict.3).
Direct water jets so as not to let water overflow from the tank.
4. Insert the intake strainer (S) onto connector stem (A) (Pict.5).
Avoid directing the water jets against the Strip-Light(s) of the canopy
The height of the intake strainer is high enough to suit the most standard aqua-
rium decorations. When decorating the aquarium, ensure it remains at least 5
cm from the gravel bottom at all times to prevent it from sucking gravel or sand
and ensure that no decorations block the passage of water. Ornaments and rocks
Important: keep plugs (P) & (Q) for any future use.
should be positioned while the aquarium is still dry.
CAUTION! Never force Connector Stems (A) sideways, as this may damage
second stem (A) (Pict.3).
the output/input systems and the glass tank.
The height of the intake strainer is high enough to suit the most standard aqua-
rium decorations. When decorating the aquarium, ensure it remains at least 5
cm from the gravel bottom at all times to prevent it from sucking gravel or sand
The height of the intake strainer is high enough to suit the most standard aqua-
If in the event a different filtration system is used, which does not require the inlet/outlet systems supplied
and ensure that no decorations block the passage of water. Ornaments and rocks
rium decorations. When decorating the aquarium, ensure it remains at least 5
this unit (e.g. an internal filter), restore the initial conditions by removing the 2 connector stems (A) and cl
should be positioned while the aquarium is still dry.
cm from the gravel bottom at all times to prevent it from sucking gravel or sand
openings (O) and (I) with plugs (P) & (Q). Plug (Q) ensures a watertight seal and has to be inserted into i
CAUTION! Never force Connector Stems (A) sideways, as this may damage
and ensure that no decorations block the passage of water. Ornaments and rocks
by pressing it. Plug (P) is designed to protect plug (Q) and ensure that plug (Q) remains in its seat proper
the output/input systems and the glass tank.
should be positioned while the aquarium is still dry.
plug (P) by hand only until it will go without forcing it. DO NOT USE ANY TOOLS, AS DOING SO MAY D
CAUTION! Never force Connector Stems (A) sideways, as this may damage
THE UNIT.
the output/input systems and the glass tank.
Output Output
Nozzle (N) Nozzle (N)
Intake
Intake
Strainer (S)
Strainer (S)
Output Output
Stem (B) Stem (B)
Pict. 4 Pict. 5
Pict. 4
OUTPUT
Tank opening
Plug (P)
Plug (Q)
10
10
Pict. 6
Pict. 5
Pict. 6
Connector
Stem (A)
Ring Nut (R)
O
INTAKE
I
GROUP GROUP
Locate the 2 openings (I) and
(O) in the tank bottom glass
and the corresponding holes
in the cabinet
Locate the 2 openings (l) and
(O) in the tank bottom glass
and the corresponding holes in
Locate the 2 openings (l) and the cabinet
(O) in the tank bottom glass
and the corresponding holes in
the cabinet
Plug (P+Q)
Plug (P+Q)
Pict. 1
Pict. 1
Connector
Stem (A)
Connector
Stem (A)
Output
Nozzle (N)
Output
Pict. 2
Stem (B)
Pict. 2
Ring Nut
(R)
Pict. 3 Pict. 4
10
Locate the 2 opening
(O) in the tank botto
and the correspondin
the cabinet
Plug (P+Q)
Pict.
Connector
Stem (A)
Pict. 2
Intake
Strainer (S)
Pict. 5 Pict. 6
7