Installation - Conrad 75 17 25 Bedienungsanleitung

O P E R A T I N G I N S T R U C T I O N S
6.35 mm CCD Colour Camera 420 TVL,
3.7 mm
Item-No. 75 17 25
Intended Use
This 6.35 mm (1/4") colour camera is intended for visual surveillance and protecting secluded or
critical areas (e.g. entrance areas, surveillance of underground car parks).
The product is only intended for dry indoor locations.
The voltage is supplied via 12 V/DC (a suitable power transformer is available as an option).
Please bear in mind that it is prohibited by law to observe strangers with a camera without their
knowledge and consent.
Do not operating the product in any other way than that described above. This could lead to
damage to the product, which may give rise to hazards such as short circuit, fire and electric
shock. The product must not be modified or converted. Always observe the safety instructions
included in these operating instructions. Please, read the operating instructions carefully and
keep them for later reference.
Package Contents
• Camera
• Mounting bracket
• Installation base
• Installation material
• Operating Instructions
Explanation of the Symbols
The lightening symbol in a triangle is used to alert you to potential risks for personal
injury, such as electric shock.
This symbol, with an exclamation mark in a triangle, indicates particular dangers
associated with handling, function or operation.
The „Hand" symbol indicates special tips and operating information.
Safety Instructions
The warranty will be void in the event of damage caused by failure to observe
these safety instructions! We do not assume any liability for any
consequential damage!
Nor do we assume liability for damage to property or personal injury caused
by improper use or failure to observe the safety instructions. The warranty
will be void in such cases.
• The camera must not be modified or converted, as not only will the CE approval
become void but also the warranty.
• The camera should not be exposed to extreme temperatures, direct sunlight,
intense vibrations, damp or heavy mechanical stress.
• Falls from a low height can damage the camera.
• If the device is used with other devices e.g. a monitor, the operating instructions
and safety notices for the connected devices must be followed.
• The use of the surveillance camera system does not replace the personal super-
vision of children, or people who require special assistance, but only serves as a
support to this supervision.
• After rapid changes in temperature, the camera requires some time to stabilise,
in order to adjust to the ambient temperature, before it can be used.
• Electronic devices are not toys and should be kept out of the reach of children!
• Please contact a qualified person if you are unsure about the safety and the correct
use of the system components.
• Never leave the packaging material lying around unattended. Plastic film/bags
etc. can be dangerous playthings for children, there is a risk of suffocation.
• If you have reason to assume that safe operation is no longer possible, dis-
connect the device immediately and secure it against inadvertent operation.
It can be assumed that safe operation is no longer possible if:
- the device is visibly damaged,
- the device no longer works and
- if the device was stored under unfavourable conditions for a long period of time
or
- it has been subjected to considerable stress in transit.
• The accident prevention regulations of the association of compensation insurers
must be followed when using all electrical facilities and equipment in commercial
locations.
• The product is only intended for dry indoor locations.
• The power is supplied via 12 V/DC (a suitable wall plug transformer is available
as an option).
• Ensure that all the electrical connections and connection cables between the
different devices and any extension cables comply with the regulations and com-
ply with the operating instructions.
www.conrad.com
Version 12/09
°

Installation

Proceed as follows, to ensure the correct installation:
• Find a suitable location for mounting the camera.
• Two mounting brackets are provided. One is used for
ceiling mounting the other one is a mounting plate for
hidden installation. Use the desired mounting bracket,
mark the fixing holes for the bracket, or the plate, where it
is to be installed.
• Drill the holes.
• Fasten the mounting base into place using appropriate
installation material.
• Screw the camera on to the mounting base.
• Adjust the camera to the desired position and then tighten
the locking screws on the mounting base.
Connection
Proceed as follows to make the correct connections:
• Connect the BNC connector of the camera to the video input on your display (e.g. monitor).
• Connect the low voltage plug from your power transformer (not included in the delivery) to the
low voltage connection on the camera.
• Plug the power transformer into a domestic mains socket (230 V/AC 50 Hz).
• Turn your display device on and set the appropriate channel, to enable the display function.
• When installing / mounting the appliance, make sure that the connection cable is
neither pinched nor damaged by sharp edges.
• Disconnect the power supply from the power socket if the unit is not to be used
for a while.
• Disconnect the camera from the power supply before cleaning.
• For safety reasons, disconnect the camera from the power supply during
thunderstorms.
• Never pour fluids out above electrical devices.
• Maintenance, adjustment and repair may only be carried out by a qualified
specialist or a specialised repair shop.
• If you have any questions, which are not answered in this manual, please contact
our technical service or another specialist.
None of the connection cables must be bent or squeezed. This can result in
malfunctions, short circuits and defects in the device.
Make sure that cables are not damaged when drilling or bolting into place.
Take care not to place the device in direct sunlight and protect it from vibration,
dust, heat, cold, and moisture. Further, please observe the values for the operating
temperature range stated in the „Technical Data".
Do not point the camera directly toward a source of bright sunlight or towards strong
or indirect illumination as this may lead to overexposure and a fuzzy picture.
To provide the suitable voltage supply, an optional power transformer is
required (recommended: 12 V/DC, 300 mA, plug polarity: inside=plus,
outside=minus). When acquiring this power transformer, check that the
polarity of the low-voltage plug of the power transformer corresponds to the
polarity marked on the low-voltage connector of the camera.
The wrong polarity can cause damage to the camera!
Installation options