Maintenance; Operation - MC Crypt GLP-08 Bedienungsanleitung

Installation on the stand
• Mount the stand with the bore holes in the stand foot or place it at suitable location.
• Screw the stand to the stand thread on the bottom of the laser.
• Secure the fixture by tightening the counter nut (knurled head screw) to the tripod.
• Set the incline angle of the stand as desired and tighten the clamping screws on the joints.
Installation with a mounting bracket
• Install the laser effect device using a mounting bracket on the ceiling, the wall or on a suitable
crossbeam. When installing it, make sure that the device cannot swing freely .
• Secure the device with fastenings that are compatible with the fastening surface and suitable
for carrying the weight of the light effect device.
• Secure the installation with an additional suitable safety restraint cable or net. The safety
restraint cable or net must be able to support the light effect device in the event of a fault in the
main support system.
• Set the desired angle of inclination and tighten the two bracket locking screws well.
Controls and Parts
(1) Microphone MIC
(2) Laser outlet - Attention, here the laser beam is released
(3) AUTO/MUSIC Switch
(4) Fan
(5) Functional switch 1-2-3
(6) Connection DC5V
Connecting the Power Adaptor
The mains socket, to which the laser is connected, must be easily accessible
so the device can be quickly separated from the mains voltage in the case of
a fault.
Do not let the mains cable come into contact with other cables.
Be careful when handling the mains cables and mains connectors. Mains
voltage can give severe electric shocks, which can be fatal.
Do not leave the cables trailing free; route them in an orderly and professional
way to prevent accidents.
• Plug the enclosed power adaptor's low-voltage plug into the DC5V (6) socket on the side of
the device.
• Plug the power unit into the wall socket.

Operation

• The desired operation mode is selected by means of the functional switch 1-2-3 (5) and the
AUTO/MUSIC (3) switch:
Functional switch 1-2-3 (5)
1 Laser effect with blinking LED effect
2 Laser effect without LED effect
3 Device is switched off
AUTO/MUSIC Switch (3)
MUSIC The laser effect is controlled by the beat of the music.
AUTO The light effect is now controlled via the integrated controller.
Handling
• Never switch the laser effect device on and off at short intervals. This will considerably reduce
the working life of the device.
• The device is not suitable for continuous use. Pauses in operation increase the working life of
the product. We recommend to let the laser cool down after a two-hour operating time before
you put it into operation again.
• Never switch on the device immediately after it has been taken from a cold into a warm
environment. The condensation that forms might damage your unit.
Allow the device to reach room temperature before switching it on. Wait until the condensation
has evaporated.
• To ensure sufficient ventilation, do not cover the device. In addition, the air circulation must not
be obstructed by objects such as magazines, tablecloths or curtains.

Maintenance

Before cleaning the laser, disconnect it from the power supply (disconnect the
power adaptor).
Strictly protect the device against dampness or moisture entering the device.
The outside of the device should be cleaned with a soft, slightly damp cloth or dry brush.
Never use aggressive cleaning agents or chemical solutions as these may damage the surface
of the housing.
Disposal
Dispose of an unserviceable product in accordance with the relevant statutory
regulations.
Technical Data
Operating voltage (Adaptor) ....................100-240 V/50/60 Hz
Operating voltage (Laser) ........................5 V DC
Power consumption ................................0.2 / 6 W Standby/max.
Laser output ............................................<1 mW
Wavelength..............................................532/660 nm
Laser class ..............................................2
Dimensions (without mounting bracket) ..160 x 115 x 60 mm
Mass ........................................................420 g
Range of operating temperature..............+15 to +30 °C
This product complies with the national and European legal requirements.
These operating instructions are a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data
processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited.
These operating instructions represent the technical status at the time of printing. Changes in technology and equipment reserved.
© Copyright 2011 by Conrad Electronic SE.