Werbung
Verfügbare Sprachen
Verfügbare Sprachen
• The minutes are flashing; set them with the button "UP" or "DOWN" and then briefly press the button "SET"
for confirmation.
• Now the number of hours is flashing for the setting of the time zone. Set it with the button "UP" or "DOWN"
(setting is possible between -12h and +12h) and then briefly press the button "SET" for confirmation.
• Now the setting for the summer/winter time is flashing (symbol "DST" in the display). Choose "ON" (turned
on) or "OFF" (turned off) by using the "UP" or "DOWN" button and then briefly press the button "SET" for
confirmation.
• The setting mode will now be ended, the display shows the time again.
Alarm function
a) Displaying the alarm times
Press the "SET" key briefly to switch between the current time, the alarm time 1 ("AL1" in the display) and the
alarm time 2 ("AL2" in the display). If no key is pressed for several seconds, the time will be displayed again.
b) Setting the alarm time
• Press the "SET" key briefly for several times to select the alarm time 1 ("AL1" in the display) or the alarm
time 2 ("AL2" in the display).
• When the alarm time "AL1" or "AL2" is displayed, hold the "SET" button for about 2 seconds until the hours
of the alarm time are flashing.
Set the hours using the "UPì or "DOWN" button (keep it pressed to enter the quick adjustment mode).
Press the "SET" key briefly to adjust the minutes of the alarm time.
• Set the minutes using the "UP" or "DOWN" button (keep it pressed to enter the quick adjustment mode).
Briefly press the "SET" button to save the setting. The alarm function is switched on automatically.
c) Switching on/off the alarm function
By briefly pressing the "ALM" button both alarm times can be switched on or off. A bell symbol with a number
"1" or "2" appears if the respective alarm time is turned on.
d) Stop alarm signal & "SNOOZE" function
When the alarm signal is emitted at the pre-set alarm time (a bell symbol flashes additionally), it can be
stopped by briefly pressing a key (not the "RESET" key) on the rear side.
If the wide button on the top side is pressed, the alarm signal will be interrupted for about 5 minutes ("Zzz"
flashes between the display of the hours and the minutes) and will then start again (snooze function). Press
the "ALM" key to abort the snooze function.
e) Selecting the alarm signal
Select between 3 different functions by using the sliding switch on the right in the battery compartment:
Only acoustic signal of the radio alarm clock
Only vibration alarm via the vibration module
+
Acoustic signal of the radio alarm clock and vibration alarm via the vibration module
f) Switch the vibration module on/off
On the bottom side of the vibration module there is a sliding switch that is used to turn the module on ("ON") or
off ("OFF"). Only when switched on, a vibration alarm can be performed when the radio table clock activates it.
Switch the temperature unit
Briefly press the button "DOWN" in order to switch between °C (degree Celcius) and °F (degree Fahrenheit).
Activate background lighting
Press the wide key on the top side of the radio alarm clock briefly in order to activate the lighting for about
5 seconds.
Battery replacement
a) Radio alarm clock
Both batteries serve as support batteries if the light that reaches the solar cells is not sufficient. If you notice
that the contrast of the display is decreasing (e. g. during activation of the background lighting), replace the
two batteries. When exchanging the batteries all settings are lost; proceed as you did during the first start-up.
b) Vibration module
If the vibration module no longer works, replace the batteries. For safety reasons the vibration module does
not have a display or suchlike.
On/off switch
On the left in the battery compartment you can see a switch that is labelled with "ON" and "OFF". By means
of this switch the radio table clock can be turned off (switch position "OFF"), e. g. during transport or storage.
For normal operating mode the switch must be set to position "ON".
Location for Installation
Select an even, flat and stable installation location. Protect valuable furniture surfaces by using an appropri-
ate underlay otherwise scratch marks can occur.
Positioning of the vibration modul
The vibration module should not be inserted in to a pillow or similar. You may unintentionally wake up through
the hard housing, if you lay on it during sleep. Place it e. g. at the edge of the bed so that it is situated between
the mattress and bed frame.
The vibration module is not a toy, never place in the beds of children.
Maintenance and Cleaning
The product does not require any maintenance, never take it apart.
Please use a dry, clean, soft cloth for cleaning. Do not apply too much pressure on the display, as it can be
damaged. Furthermore, scratches can occur.
Do not use any chemical cleaning agents, which might discolour the plastic housing.
Disposal
a) Product
Electronic devices are recyclable waste and must not be disposed of in the household waste!
Dispose of the unserviceable product according to the relevant statutory regulations.
b) Batteries and rechargable batteries
The end user is legally obliged (Battery Regulation) to return used batteries and rechargeable batteries. Do
not dispose of used batteries via the domestic waste!
Batteries/rechargeable batteries containing harmful substances are marked with the symbols
shown, to indicate that disposal in the domestic waste is forbidden. The symbols for the rele-
vant heavy metals are: Cd=cadmium, Hg=mercury, Pb=lead (designation can be found on bat-
tery/rechargeable battery under the trash icons on the bottom left).
You can return used (rechargeable) batteries free of charge at the official collection points in
your community, our stores, or wherever (rechargeable) batteries are sold!
You thus fulfil your statutory obligations and contribute to the protection of the environment.
Technical Data
a) Radio table clock
Current supply ............................2 batteries of type AA/Mignon
Interior temperature display ........-10° to +50° (14°F to 122°F)
Accuracy ......................................+/- 1°C
Measuring interval ......................12 seconds (not during DCF recognition or an alarm signal)
Alarm function..............................2 alarm times programmable, snooze function
Dimensions ..................................Approx. 140 x 59 x 105mm (W x L x H)
b) Vibration module
Current supply ............................2 batteries of type AA/Mignon
Dimensions ..................................Approx. 142 x 60 x 23mm (L x W x H)
Declaration of Conformity (DOC)
We, Conrad Electronic, Klaus-Conrad-Strafle 1, D-92240 Hirschau, hereby declare that this product conforms
to the fundamental requirements and the other relevant regulations of the directive 1999/5/EG.
You can find the declaration of conformity at www.conrad.com.
These operating instructions are a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240
Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or
the capture in electronic data processing systems require the prior written approval by the editor.
Reprinting, also in part, is prohibited.
These operating instructions represent the technical status at the time of printing. Changes in
technology and equipment reserved.
© Copyright 2008 by Conrad Electronic SE.
Werbung
