Technical Data; Maintenance And Cleaning - VOLTCRAFT BS-20 Bedienungsanleitung

Switching the Endoscope On and Off
Press the On/Off Switch (2). The Endoscope turns on. After a short time, the camera image
appears on the monitor.
To turn off, press the On/Off Switch again. The device turns off.
Camera lighting
To enable the Endoscope to be used in totally dark areas, the camera head camera has an inte-
grated, stepwise, dimmable LED light.
Press the button „brighter" (3), to switch on the light. Now, each time you press the button the
light becomes brighter.
You can reduce the brightness, or switch off the light, by pressing the button „darker" (4). Now,
each time you press the button the light becomes darker.
Adjust the lighting, so that the image displayed on the monitor is not over-exposed or under-
exposed.
Press the On/Off Switch, to turn the device off (2). The device turns off.
To Rotate the Camera Image by 180°
By using a key combination, the camera image can be rotated by 180°. This facilitates the con-
trol of the camera image in unfavourable positions.
In normal camera mode, press the buttons „brighter" (3) and „darker" (4) at the same time. The
camera image will be displayed on the monitor rotated by 180°.
This function is automatically deactivated when the device is switched off.
NTSC video output
The Endoscope has the option to display the image for recording and documenting, using an
integrated NTSC video output.
The Video-Out jack is located on the underside of the handle (1). Please use the video cable
supplied to connect to your play back or recording device. Switch the Endoscope on.
Plug the phono jack in the socket (1) of the Endoscope.
Connect the RCA connectors to the video input of your play back or recording device.
Then switch the play back device on and select the video input.
For proper replay of the NTSC video signal, you will need a multisignal
device. Modern devices have automatic video signal detection. If not, set the
video input manually to „NTSC". Please follow the instructions in the oper-
ating manual for your playback or recording device.
The camera image will be displayed, if you have connected the device properly and if you are
using the correct video source.
Press the On/Off Switch, to turn the device off (2). The device as well as the video output are
turned off.
Top piece with mirror, magnet and hooks
The top piece with mirror, magnet and hooks can be placed on the camera head. In this way,
lost metal parts can be searched for and found.

Maintenance and Cleaning

You do not need to service the product, apart from occasional cleaning. Use a soft, antistatic
and lint-free cloth for cleaning. Do not use abrasive or chemical cleaners.
Carefully rinse the gooseneck of the Endoscope with clean water, after use in liquids and dry it
before storing it in the case.
Disposal
Electronic products are raw material and do not belong in the household waste.
When the device has reached the end of its service life, please dispose of it,
according to the current statutory requirements, at your local collecting site.
Disposal in the domestic waste is not permitted!
Disposal of used batteries
As a consumer you are required (Battery Ordinance) to responsibly dispose of all
used batteries and rechargeable batteries; do not dispose of used batteries in
the household waste!
You can return used (rechargeable) batteries free of charge at the official
collection points in your municipality, our stores, or where ever (rechargeable) bat-
teries are sold!
You thus fulfil the legal requirements and make your contribution to pro-
tecting the environment!

Technical Data

TFT monitor
Resolution
Focus
Field of view
White Balance
Exposure
Video format
Camera lighting
Power Supply
Power input
Ambient/ operating temperature
Gooseneck Length
Min. bending radius
Camera Diameter
Protection Class gooseneck
Weight without accessories
Impressum /legal notice in our operating instructions
These operating instructions are a publication by Voltcraft ® , Lindenweg 15, D-92242 Hirschau/Germany, Phone +49 180/586 582 7 (www.voltcraft.de).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data processing
systems require the prior written approval by the editor. Reprinting, also in part, is prohibited.
These operating instructions represent the technical status at the time of printing. Changes in technology and equipment reserved.
© Copyright 2010 by Voltcraft ®
6 cm (2.4") Screen size
320 x 234 pixels
30 mm
54 °
automatic
automatic
NTSC
2 LEDs, white
6 V/DC (4 x AA)
max. 200 mA
0 to +45°C
approx. 90 cm
45 mm
10 mm
IP67 (waterproof)
approx. 370 g