Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
OpERATION
Only immerse the camera head and camera neck in liquids that are voltage
free! The camera neck is not to be submerged further than the marking "mAX
water Level".
The endoscope may only be used for inspection of dead systems. The camera
head is made of metal and can lead to short circuits. for safety reasons,
disconnect all system parts from the power supply before every inspection.
Avoid strong mechanical strains or vibrations. make sure you never go below
the minimum bending radius of 45 mm.
a)
General
1.
Press the on/off button to switch the device on. The power LED will turn on and the camera
image will appear in the monitor.
2.
Two LEDs are integrated in the camera head.
-
Press the button ↑ to increase the brightness of the LEDs.
-
Press the button ↓ to reduce the brightness of the LEDs or to turn the lighting off entirely.
Set the lighting so that the camera image displayed is neither overexposed nor
underexposed.
3.
Press the buttons ↑ and ↓ simultaneously to rotate the image by 180º.
4.
Press the on/off button to switch the device off.
b)
Video output
1.
Connect the video cable jack to the video output, to the right of the display.
2.
Connect the yellow cinch connector to the corresponding socket of a TV set or monitor.
3.
This will make the image on the monitor go off, and the camera image will then be displayed
on the TV or monitor screen.
c)
Attachments
1.
If required, mount one of the three attachments (magnet, hook, mirror) into the small recess
below the camera head.
2.
Before use, ensure that the mounting ring of the attachment is locked.
d)
Ring bolt
There is a ring bolt fitted above the monitor. Attach this bolt to a carrying strap (not included), if
required, to facilitate hands-free operation.
mAINTENANcE AND cLEANING
•
The device requires no servicing on your part apart from occasional cleaning. Only use a soft,
anti-static and lint-free cloth for cleaning.
•
Do not use abrasive or chemical cleaners.
•
Flush the gooseneck camera thoroughly with clean water after each use in liquids and dry it
off before returning it to the case.
•
To clean the camera lens, use a small brush or cotton swab.
DISpOSAL
a)
product
Electronic devices are recyclable waste and must not be disposed of in the household
waste!
At the end of its service life, dispose of the product according to the relevant statutory
regulations.
b)
(Rechargeable) batteries
You as the end user are required by law (Battery Ordinance) to return all used batteries/
rechargeable batteries. Disposing of them in the household waste is prohibited!
Batteries/rechargeable batteries that include hazardous substances are labelled with
these icons to indicate that disposal in domestic waste is forbidden. The descriptions
for the respective heavy metal are: Cd=cadmium, Hg=mercury, Pb=lead (the
designation is written on the rechargeable battery e.g. under the rubbish can symbols
depicted at the left).
You can return used batteries/rechargeable batteries free of charge at the official
collection points of your community, in our stores, or wherever batteries/ rechargeable
batteries are sold!
You thus fulfil your statutory obligations and contribute to the protection of the environment.
TEchNIcAL DATA
Operating voltage ................. 4 x 1.5 V AA battery (not included)
Current consumption ............ max. 350 mA
Display .................................. 6.1 cm (2.4") TFT
Resolution ............................. 480 x 234 pixels (monitor), 640 x 480 pixels (camera)
Video format ......................... PAL
Camera lighting .................... 2 white LEDs
White balance ....................... automatic
Exposure .............................. automatic
Field of view .......................... 5 4º
Depth of field ........................ 3 – 6 cm
Operating temperature ......... 0 to +45 ºC
Operating humidity ............... 15 – 85 % RH
Storage temperature ............. - 10 to +50 ºC
Storage humidity ................... 15 – 85 % RH
Gooseneck length ................. 88 cm ±2 cm
Camera Ø ............................. 9.8 mm
Min. bend radius ................... 45 mm
Cable length ......................... 1.5 m
Dimensions (W x H x D) ....... 88 x 223 x 119 mm
Weight .................................. approx. 330 g
Legal notice
These operating instructions are a publication by Voltcraft®, Lindenweg 15, D-92242 Hirschau/Germany, Phone +49 180/586 582 7
(www.voltcraft.de).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data processing
systems require the prior written approval by the editor. Reprinting, also in part, is prohibited.
These operating instructions represent the technical status at the time of printing. Changes in technology and equipment reserved.
© copyright 2011 by Voltcraft®
Werbung
Inhaltsverzeichnis
