Technical Data; Maintenance And Cleaning - VOLTCRAFT BS-14 MM/25M Bedienungsanleitung

c) Using the reel
1. The guide ring on the reel frame is for safely guiding the push cable. Before using the
camera, guide the camera and push cable though the guide ring. Pull the camera and
push cable from the inner circle of the reel and through the guide ring. Use the hook
properly to prevent snapping the camera cable.
2. Handle the connection cable with care; it must not get into the reel. Slowly guide the
endoscope camera into the pipe system to be inspected. Push the camera cable
forwards slowly and carefully. The camera may be damaged if force is used or if you
proceed too quickly.
3. Do not pull on the camera with force.
4. After you have finished inspecting, carefully guide the camera with the camera cable
backwards and wrap the endoscope cable onto the reel. Carefully guide the endoscope
cable backwards with your hand to prevent damage. Do not wrap the cable by turning
the reel. Wipe the camera neck with a damp cloth before winding it back up and then
dry it.
5. Secure the cable reel to frame with hook and loop fastener to prevent accidental
damage during transport. Secure the camera head and connection socket to protect
against damage.
d) Operation
1. Turn the endoscope on.
2. Set the brightness of the camera LEDs. Information on controlling the LED brightness
can be found in the operating instructions of the connected endoscope.
3. The length counter will reset to zero when the controller unit is turned on. The counter
can also be reset using the menu. For further information please refer to the operating
instructions for BS-1500T (Item no. 1340787).
4. Turn off the endoscope after you have finished using it.

MAINTENANCE AND CLEANING

• The device does not require maintenance except for cleaning and lubrication. The ball
bearings on the reel should be lubricated with a small amount of oil or grease from time to
time. Use resin-free and acid-free products.
• Use a small brush or a cotton bud to clean the camera lens.
• Use a soft, antistatic and lint-free cloth to clean the device. Do not use any abrasive or
chemical cleaning materials.
• Let the camera head dry before putting the camera cap on as thread protection.
• After inserting the camera neck into liquid, rinse it thoroughly with clean water and dry it
before storing it for the next use.
DISPOSAL
Electronic devices are recyclable waste and must not be disposed of in the
household waste.
At the end of its service life, dispose of the product according to the relevant
statutory regulations.
You thus fulfil your statutory obligations and contribute to the protection of the environment.

TECHNICAL DATA

Camera-Ø ............................................14 mm
Adapter cable length .............................2 m (extended), 60 cm (coiled)
Image sensor ........................................CMOS
Depth of field ........................................5 - 60 cm
Resolution .............................................640 x 480 Pixels
White balance .......................................Automatic
Exposure ..............................................Automatic
Illuminant ..............................................8 LEDs (white)
Illuminance ...........................................max. 3000 lx (at a distance of 20 mm)
Min. bending radius ..............................>10 cm
Protection type ......................................IP67 (camera, camera neck waterproof)
Operating conditions .............................-20 to +60 °C, max. 95 % RH (non-condensing)
Storage conditions ................................ -20 to +60 °C, max. 95 % RH (non-condensing)
Camera neck length .............................18 m
Push cable length .................................25 m
Dimensions (W x H x D) .......................approx. 45 x 45 x 25.5 cm
Weight ..................................................approx. 5.3 kg
Designed for BS-1500T endoscope - Item no. 1340787
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com). All rights
including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data
processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication
represents the technical status at the time of printing.
Copyright 2020 by Conrad Electronic SE. *2183202_v1_0220_02_dh_m_en