EINHELL BT-SP 1300 Originalbetriebsanleitung Seite 15

Anleitung_BT_SP_1300_SPK1:_
When you have finished work, switch off the
machine. To do this, press the red button "0" and
close the yellow cover (1). Then disconnect the
machine from the mains supply.
Remove the chips and dust from the feed table
(13), planing table (14) and knife block (23) after
the machine has reached a complete
standstill.
Return the planing knife cover (12) to its original
position.
12. Thicknessing
12.1 Adjustment (Fig. 10)
Place the hand crank (4) on the post on the
planing table (14) and turn it to adjust the
thicknessing table (20) to the required height.
The set angle can be read off the scale (29).
12.2 Fitting the chip extractor (Figure 1/10/14/18)
Undo the locking knob (32) and pull the planing
knife cover (12) forwards as far as possible.
Place the chip extractor (5) on the planing table
(14). Ensure that the stop pins and the securing
screw (34) are in the appropriate holes and are
engaged in the internal threads on the planing
table (14) and that the recess (b) is on the safety
switch (e).
Turn the securing screw (34) until the chip
extractor (5) is secure.
Fit the 100 mm chip extractor adapter (27) and, if
necessary, the 35 mm chip extractor adapter
(28) to the chip extractor (5).
Connect the plane to a chip extraction system
(not supplied).
12.3 Thicknessing mode (Fig. 11/13)
Connect the mains plug to the mains lead. Open
the yellow cover (1) and press the green button
"I" to start the plane.
Place a workpiece on the thicknessing table (20).
Guide the workpiece towards the feed table (13).
When you have finished work, switch off the
machine. To do this, press the red button "0" and
close the yellow cover (1). Then disconnect the
machine from the mains supply.
Remove the chips and dust from the
thicknessing table (20) and knife block (23) after
the machine has reached a complete
standstill.
02.09.2010 11:29 Uhr Seite 15
13. Changing the knives (Figure 15/16)
Important: Always pull the mains plug before
changing the knives.
Remove the parallel stop following the
instructions in 9.1 in reverse.
Pull the planing knife cover (12) forwards as far
as possible so that the entire knife block (23) is
exposed.
Undo the clamp screws (c) by turning them
clockwise using the open-ended spanner (17)
supplied. Turn the knife block (23) so that the
latch (22) can be pulled out with the knife (21).
Clean all the relevant parts and the knife slots in
the knife block (23).
Fit the latch (22) with the new knife (21) and
align them with the side of the knife block.
Place the blade adjustment block (15), as shown
in Figure 16, on the surface of the planing table
(14). Ensure that the knife (21) touches both
sides of the blade adjustment block (15).
Tighten the clamp screws (c) counter-clockwise
using the open-ended spanner (17) supplied.
Return the planing knife cover (12) to its original
position so that the knife (21) is covered.
Important!
Only use knives which have been produced
specifically for this machine. If you use other knives
there is a risk of injuries as a consequence of a lack of
control. Avoid over-tightening and the possibility of
the thread becoming detached. If the latch (22) or the
screws have worn out threads they must be
immediately replaced.
14. Maintenance (Figure 1/13)
Important: Pull the mains plug before starting and
maintenance work.
14.1 Machine
Lubricate the following parts periodically after around
10 hours of service:
Bearings for the feed/discharge rollers and anti-
kick claws (24)
Bearings on the belt roller and pulley
Grub screws to adjust the height of the
thicknessing table (20)
Use only dry lubricant.
GB
15