Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
D
e
s
c
r
i
p
t
i
o
n
o
f
D
e
s
c
r
i
p
t
i
o
n
o
f
/
Pos
Denomination
1.
Agitator
2.
Mortar beater
a) Bar
b) Beater attachment
3.
ON / OFF-switch
4.
Trip switch
5.
Speed control
6.
2-speed switch
7.
Handle
8.
Shaft
9.
Carbon brush cover
10.
Carbon brushes (2pcs)
11.
Spanners SW 22
12.
Spanners SW 19
13.
Safety label
14.
Disk beater
15.
Spiral beater
Chucking the beater
Screw the bar (2a) on the shaft (8). Secure the bar
using the spanners (11/12).
Screw the beater attachment (2b) on the bar (2a) and
secure it using the spanner (11).
S
S
Do not use any device where the switch can not be
switched on and off. Damaged switches must be repaired
or replaced immediately by the customer service.
Check that the machine is completely and correctly assem-
bled.
Before each use, check
Connection cables for defects (cracks, cuts, etc.).
−
Do not use any defective cables.
there are no damages at the machine
−
(see "safe working")
that the beater is properly secured.
−
14
d
e
v
i
c
e
/
S
p
a
r
e
p
a
r
t
s
d
e
v
i
c
e
/
S
p
a
r
e
p
a
r
t
s
Order-No.
RL 1400
372612
Ø140 mm
372661
372659
372562
372657
372662
372613 Ø114 mm
372614 Ø140 mm
A
s
s
e
m
b
l
y
A
s
s
e
m
b
l
y
t
a
r
t
-
u
p
t
a
r
t
-
u
p
Mains connection
Compare the voltage given on the machine model plate e.g.
230 V with the mains voltage and connect the machine to
the relevant and properly earthed plug.
Connect the machine via a 30 mA fault current safety
switch.
Do not use any defective connection cables.
Use connecting or extension cables up to a length of 1.5 m
featuring a core cross section of at least 25 mm².
In case of disadvantageous power system conditions short-
term voltage reductions can occur during the starting pro-
cess of the device which can influence other devices (e.g.
jittering of a lamp). No failures are expected when the house
service connection has a continuous currect-carrying capac-
ity greater than 100 A per phase.
Main fuse: 10 A
Switching on/off
Do not use any device where the switch can not be
switched on and off. Damaged switches must be repaired
or replaced immediately by the customer service.
Switching on
Operate the trip switch (4) at first. Press the ON/OFF
button (3) on the handle.
Start the machine at the lowest rotational speed (Level
1).
Switching off
Release the ON/OFF handle button.
This machine is not suited for continuous operation.
Speed control
With this type, the motor's speed and thus the agitator perfor-
mance can be adjusted. (Level 1 - 6).
You can continuously adjust the speed with the speed
control (5).
•
Level 1
Min. power = SLOW.
•
Level 6
max. power = FAST.
2- speed gear
The device is equipped with a 2-speed gear.
For the speed selection turn the switch (6) by 180°.
1. speed: 0 min
bis 570 min
–1
2. speed: 0 min
bis 760 min
-1
Only operate this switch at standstill.
–1
-1
Werbung
Inhaltsverzeichnis
