Inhaltsverzeichnis
Werbung
GB
TABLE SAW
Always read the instruction for electrical
products carefully before use. It will
help you understand your product more
easily and avoid unnecessary risks.
Keep this instruction manual in a safe
place for future use.
Contents
1. Technical specifications
2. Safety instructions
3. Assembly instructions
4. Operation
5. Maintenance
1. TECHNICAL
SPECIFICATIONS
Voltage
230-240 V~
Frequency
50 Hz
Power input
1500 W
No load speed
4500/min
Saw blade dimensions
254x16x2.8mm
Number of teeths
Z40
Measurements of bench
667x430 mm
Dust extraction outlet
30(20) mm
Weight
37 kg
Lpa (sound pressure level) 99.3 dB(A)
Lwa (sound power level)
112.3 dB(A)
Product information
Fig. A
1. Protective cap
2. Fence
3. Bench inlay
4. Mitre handle
5. Height handle
6. Measurement set-up for fence
7. On/off switch
8. Thermic safety switch
9. Workbench
Check first whether or not the delivery has been
damaged by transport and/or whether all the
parts are present.
06
2. SAFETY INSTRUCTIONS
Explanation of symbols
In this manual and/or on the machine the
following symbols are used:
Denotes risk of personal injury, loss of
life or damage to the tool in case of
non-observance of the instructions in
this manual.
Denotes risk of electric shock! Always
check that the power supply
corresponds to the voltage on the rating
plate.
Additional safety instructions
1. When using the saw blades with hard metal
teeth (Carbon tipped) it is advisable to use
blades with a negative or slightly positive
cutting angle. Do not use any saw blades with
deeply cut teeth. They can grip the protective
cap.
2. Attention: First carefully assemble all the parts
before starting work. Follow the procedure as
indicated.
3. If you are not familiar with using such a
machine, you would be better to be informed
first by a professional, an instructor or by a
technician.
4. Always clamp or press the workpiece firmly
against the saw guide, before you carry out
the process. The use of all possible clamping
set-ups is preferable to using your hands.
5. Important: If you are holding the workpiece by
hand for the process to be carried out, keep a
minimum distance of 100 mm from the saw
blade.
6. Always press the workpiece against the
bench.
7. Keep the saw blade sharp and check
regularly whether it rotates freely without
abnormal vibrations. Replace the saw blade if
necessary.
8. Allow the machine to rotate freely until it
reaches the maximum number of revolutions,
before you start the process.
9. Maintain the air inlets at the back and the
bottom of the bench saw machine and electric
engine for a longer machine life. Dust piles
must be removed.
10.Always lock the different degree set-ups
before you start processing.
Ferm
5. Armen til højde- og/eller geringsindstilling
er blokeret
•
Savsmuld og støv skal fjernes.
6. Motoren har svært ved at nå det
maksimale omdrejningstal
•
Forlængerledningen er for tynd og/eller for
lang.
•
Netspændingen er lavere end 230 V~.
7. Maskinen vibrerer
•
Maskinen er ikke fastskruet til
arbejdsbænken;
•
Understellet står ikke vandret på gulvet;
•
Savbladet er beskadiget.
Rengøring
Rengør regelmœssigt maskinkappen med en
blød klud, helst efter hvert brug. Sørg for at
ventilationshullerne er fri for støv og snavs. Brug
en blød klud, der er vœdet i sœbevand til at
fjerne hårdnakket snavs. Brug ingen
opløsningsmidler, så som benzin, alkohol,
ammoniak, osv. Den slags stoffer beskadiger
kunststofdelene.
Smøring
Maskinen behøver ingen ekstra smøring.
Fejl
Skulle en fejl opstå, f.eks. pga. slidtage af en
enhed, kontakt venligst serviceadressen på
garantibeviset. På bagsiden af denne manual
finder du en tegning med alle dele, der kan
bestilles.
Miljø
For at undgå transportbeskadigelse leveres
maskinen i en solid emballage. Emballagen er så
vidt muligt lavet af genbrugsmateriale. Genbrug
derfor emballagen.
Defekte og/eller kasserede elektriske
eller elektroniske maskiner skal
afleveres på en genbrugsplads.
Garanti
Lœs det separat vedlagte garantikort for
garantibetingelserne.
Ferm
DK
71
Werbung
Inhaltsverzeichnis
