Remaining Value Transfer; Selecting The Drying Programme; Debit The Programme Amount And Start; Displays During The Programme Sequence - Schulthess Spirit topLine 8040i Bedienungsanleitung

Remaining value transfer

If there is not an adequately high remaining amount
available on a Cash-Card to pay for the booking on ac-
count, a signal will sound and the message «Balance too
small» appears. By inserting a second Cash-Card, the
difference can be paid.
prePaid-Card
Selecting the wash programme
see chapter «Washing/ Selecting the wash programme»)
X Select the wash programme.
X Select additional functions.
X In the display will appear the price of the programme.

Debit the programme amount and start.

X Insert the prePaid-Card. In the display will appear in
succession the amount stored on the prePaid-Card, the
programme amount which will be deducted, as well as
the new prePaid-Card balance.
Any remaining credit balance stored in the appliance will
be set off.
X Remove the prePaid-Card.
X Start the wash programme.

Displays during the programme sequence

No credit will be shown for the duration of the wash
programme.

Re-crediting

It is possible to reverse the remaining credit onto the
prePaid-Card.
X Insert the prePaid-Card. The amount stored on the
card will appear in the display.
X Re-credit by pressing the quick wash button. In the
display will appear in sequence the remaining credit
balance which will be credited, as well as the new pre-
Paid-Card balance.
X Remove the prePaid-Card.
Re-crediting can always be made only to that prePaid-
Card from which the amount was originally deducted.
In the case of child lock switched on:
+
Remaining value transfer
If there is not an adequately high remaining amount
available on a prePaid-Card to pay for the booking on
account, this will be displayed by the whistle signal and
by the message «Saldo to small». By inserting a second
prePaid-Card, the difference can be pai d.
52
Problems
Repairs, alterations or intervention on electronic equip-
ment should only be carried out by qualified specialists.
Inexpert repairs can cause considerable damage and risk
to the user.
Only original spare parts should be used for repairs.
Please find below minor faults which you can rectify
yourself.
Error messages on the display
If the following error messages are displayed, the pro-
gramme can be restarted by pressing the start button
once the error has been rectified.
«CHILD LOCK ACTIVE»
X Hold the Quick Wash button down and press the start
button.
«CLOSE DOOR AND START»
X Push the door closed until the lock catches properly.
«PLEASE START AGAIN»
X If the door was closed subsequently, the Start button
must be pressed again.
«CHECK WATER INLET AND START»
X Turn on the tap and start again.
X Filter in water supply is blocked: Clean the filter, see
chapter «Cleaning and Maintenance /Cleaning the filter
in the water inlet».
X Interruption in water supply.
«CHECK WATER OUTLET AND START»
X Check whether the drainage hose is blocked.
X Foreign bodies block the drain pump: clean pump
according to chapter «Cleaning and Maintenance/ Emer-
gency emptying».
X The water drain provided by the customer is blocked:
Carry out an emergency discharge according to chapter
«Cleaning and Maintenance» and clean the drain si-
phon (built-in siphon).
X The position of the drain hose is too high. The maxi-
mum pumping height is 1m above ground.
«UNBALANCE NO SPINNING»
X Excessive imbalance. Laundry not spun.
X Press the start button and then the Quick Wash button
to end the wash programme.
X Open the door and redistribute the load.
X Repeat the spin cycle with the separate spin programme.
General information:
X Avoid loading the drum with one single heavy item.
Wash large and small laundry together.
«FOAM PROG. ExTEND»
X The washing machine has detected foam and taken
adequate measures. The spinning cycle of the laundry
could be completed.
 In future, please reduce the detergent quantity.