Technical Data; Noise/Vibration Information; Declaration Of Conformity - Bosch POF 1200 AE Originalbetriebsanleitung

OBJ_BUCH-323-004.book Page 16 Wednesday, September 21, 2011 12:47 PM
16 | English
23 Thumbwheel for speed preselection
24 Adjusting screws for step buffer (POF 1200 AE)
25 Tightening nut with collet
26 Open-end spanner, size 19 mm*
27 Extraction hose (Ø 35 mm)*
28 Extraction adapter*
29 Knurled screw for extraction adapter (2x)*
30 Guide rod for parallel guide (2x)*
31 Parallel guide*
32 Centring pin*
33 Wing bolt for centring pin*
34 Curve guide*
35 Router compass/guide-rail adapter*

Technical Data

Plunge router
Article number
Rated power input
No-load speed
Speed preselection
Constant electronic control
Connection for dust extraction
Tool holder
Plunge depth
Weight according to EPTA-Procedure 01/2003
Protection class
The values given are valid for a nominal voltage [U] of 230 V. For different voltages and models for specific countries, these values can vary.
Please observe the article number on the type plate of your machine. The trade names of the individual machines may vary.

Noise/Vibration Information

Measured sound values determined according to EN 60745.
Typically the A-weighted noise levels of the product are:
Sound pressure level 95 dB(A); Sound power level
106 dB(A). Uncertainty K =3 dB.
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 60745:
2 2
a =6 m/s , K=2 m/s .
h
The vibration emission level given in this information sheet
has been measured in accordance with a standardised test
given in EN 60745 and may be used to compare one tool with
another. It may be used for a preliminary assessment of expo-
sure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or poorly maintained,
the vibration emission may differ. This may significantly in-
crease the exposure level over the total working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working pe-
riod.
1 619 929 J76 | (21.9.11)
36 Router compass handle*
37 Wing bolt for coarse adjustment of
router compass (2x)*
38 Wing bolt for fine adjustment of
router compass (1x)*
39 Fine-adjustment knob for router compass*
40 Centring screw*
41 Guide rail*
42 Base spacer
(included in the "router compass" set)*
43 Guide bushing*
*Accessories shown or described are not part of the standard de-
livery scope of the product. A complete overview of accessories
can be found in our accessories program.
POF 1200 AE
3 603 B6A 0.1
W 1200
-1
min 11000–28000
mm 6/8
inch
mm
kg 3.4
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep hands warm, organise work patterns.

Declaration of Conformity

We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with the fol-
lowing standards or standardization documents: EN 60745
according to the provisions of the directives 2011/65/EU,
2004/108/EC, 2006/42/EC.
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9,
D-70745 Leinfelden-Echterdingen
Dr. Egbert Schneider Dr. Eckerhard Strötgen
Senior Vice President Engineering Director
Engineering PT/ESI
Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
31.08.2011
POF 1400 ACE
3 603 B6C 7.1
1400
11000–28000
–
6/8
¼ ¼
55 55
3.5
/II /II
Bosch Power Tools