Connecting The Units; Connection Diagram - Pioneer DEH-P7000UB Installationsanleitung

1. USB cable
Connect to separately sold USB device.
13. Note
1.5 m
Depending on the kind of vehicle,
2. Antenna jack 3. This product
the function of 3* and 5* may be
different. In this case, be sure to
15 cm
connect 2* to 5* and 4* to 3*.
1* 4. Rear output
5. Front output
3* 2*
6. Subwoofer output
8.Fuse (10 A)
9.AUX jack (3.5 ø)
5* 4*
Use a stereo mini
plug cable to connect
14. Connect leads of the
with auxiliary device.
same color to each other.
15. Cap (1*)
Do not remove cap
if this terminal is
not in use.
16. Yellow (3*) 17. Yellow (2*)
Back-up (or Connect to the constant
accessory) 12 V supply terminal.
18. Red (5*) 19. Red (4*)
Accessory Connect to terminal controlled by
(or back-up) ignition switch (12 V DC).
20. Orange/white
Connect to lighting switch terminal.
21. Black (chassis ground)
Connect to a clean, paint-free metal location.
22. ISO connector 23. Yellow/black
Note
If you use an equipment with Mute
In some vehicles, the ISO connector may be function, wire this lead to the Audio Mute
lead on that equipment. If not, keep the
divided into two. In this case, be sure to
Audio Mute lead free of any connections.
connect to both connectors.
28.To subwoofer
20 cm
31.Connect with RCA cables
output
(sold separately)
7. Wired remote input
Hard-wired remote
29.To rear output
control adaptor can
be connected (sold
separately).
30.To front output
10. IP-BUS input (Blue)
12.Multi-CD player
11. IP-BUS cable
(sold separately)
33.System remote control
24. Blue/white
Connect to system control terminal of the
power amp (max. 300 mA 12 V DC).  
34. Front speaker
 
25. Blue/white (7*)
 
Connect to auto-antenna relay control
35. Rear speaker
terminal (max. 300 mA 12 V DC).
 
26. Blue/white (6*)
 
The pin position of the ISO
36. Subwoofer
connector will differ depends on the  
type of vehicle. Connect 6* and 7*
when Pin 5 is an antenna control
37. Perform these connections when
type. In another type of vehicle,
using the optional amplifier.
never connect 6* and 7*.
38. Notes
27. Speaker leads
Front left  • Change the initial setting of this unit (refer to the
White:
operation manual). The subwoofer output of this unit is
White/black: Front left 
Front right  monaural.
Gray:
• When using a subwoofer of 70 W (2 Ω), be sure to
Gray/black: Front right 
Rear left  or subwoofer  connect with Violet and Violet/black leads of this unit.
Green:
Green/black: Rear left  or subwoofer  Do not connect anything with Green and Green/black
leads.
Rear right  or subwoofer 
Violet:
Violet/black: Rear right  or subwoofer 

Connecting the units

Note
• When this unit is installed in a vehicle without
32.Power amp
ACC (accessory) position on the ignition switch,
(sold separately)
red cable must be wired to the terminal that can
detect the operation of the ignition key. Otherwise,
battery drain may result.
32.Power amp
(sold separately)
32.Power amp
(sold separately)
ACC position No ACC position
• Use this unit in other than the following
conditions could result in fire or malfunction.
— Vehicles with a 12-volt battery and negative
grounding.
— Speakers with 50 W (output value) and 4 ohm
to 8 ohm (impedance value).
• To prevent short-circuit, overheating or
malfunction, be sure to follow the directions
below.
34. Front speaker — Disconnect the negative terminal of the
battery before installation.
— Secure the wiring with cable clamps or
adhesive tape. To protect the wiring, wrap
adhesive tape around them where they lie
35. Rear speaker
against metal parts.
— Place all cables away from moving parts, such
as gear shift and seat rails.
— Place all cables away from hot places, such as
near the heater outlet.
36. Subwoofer
— Do not pass the yellow cable through a hole
into the engine compartment to connect to a
battery.
— Cover any disconnected cable connectors with
insulating tape.
— Do not shorten any cables.
— Never cut the insulation of the power cable of
this unit in order to share the power to other
equipment. Current capacity of the cable is
limited.
— Use a fuse of the rating prescribed.
— Never wire the speaker negative cable directly
to ground.
— Never band together multiple speaker's
negative cables.
English Connecting the units

Connection Diagram

• Control signal is output through blue/white cable
when this unit is powered on. Connect it to an
1. USB cable
external power amp's system remote control or
Connect to separately sold USB device.
the vehicle's auto-antenna relay control terminal
2. Antenna jack
(max. 300 mA, 12 V DC). If the vehicle is equipped
with a glass antenna, connect it to the antenna 3. This product
booster power supply terminal.
4. Rear output
• Never connect blue/white cable to external power
5. Front output
amp's power terminal. Also, never connect
6. Subwoofer output
it to the power terminal of the auto antenna.
7. Wired remote input
Otherwise, battery drain or malfunction may
Hard-wired remote control adaptor can be
result.
connected (sold separately).
• IP-BUS connectors are color-coded. Be sure to
connect connectors of the same color. 8. Fuse (10 A)
• Black cable is ground. This cable and other
9. AUX jack (3.5 ø)
product's ground cable (especially, high-current
Use a stereo mini plug cable to connect with
products such as power amp) must be wired
auxiliary device.
separately. Otherwise, fire or malfunction may
10. IP-BUS input (Blue)
result if they are accidentally detached.
11. IP-BUS cable
12. Multi-CD player (sold separately)
13. Note
Depending on the kind of vehicle, the function
of 3* and 5* may be different. In this case, be
sure to connect 2* to 5* and 4* to 3*.
14. Connect leads of the same color to
each other.
15. Cap (1*)
Do not remove cap if this terminal is not in use.
16. Yellow (3*)
Back-up (or accessory)
17. Yellow (2*)
Connect to the constant 12 V supply terminal.
18. Red (5*)
Accessory (or back-up)
19. Red (4*)
Connect to terminal controlled by ignition
switch (12 V DC).
20. Orange/white
Connect to lighting switch terminal.
21. Black (chassis ground)
Connect to a clean, paint-free metal location.
22. ISO connector
Note
In some vehicles, the ISO connector may
be divided into two. In this case, be sure to
connect to both connectors.
23. Yellow/black
If you use an equipment with Mute function,
wire this lead to the Audio Mute lead on that
equipment. If not, keep the Audio Mute lead
free of any connections.
English
24. Blue/white
Connect to system control terminal of the
power amp (max. 300 mA 12 V DC).
25. Blue/white (7*)
Connect to auto-antenna relay control terminal
(max. 300 mA 12 V DC).
26. Blue/white (6*)
The pin position of the ISO connector will differ
depends on the type of vehicle. Connect 6*
and 7* when Pin 5 is an antenna control type.
In another type of vehicle, never connect 6*
and 7*.
27. Speaker leads
White: Front left
White/black: Front left
Gray: Front right
Gray/black: Front right
Green: Rear left or subwoofer
Green/black: Rear left or subwoofer
Violet: Rear right or subwoofer
Violet/black: Rear right or subwoofer
28. To subwoofer output
29. To rear output
30. To front output
31. Connect with RCA cables (sold separately)
32. Power amp (sold separately)
33. System remote control
34. Front speaker
35. Rear speaker
36. Subwoofer
37. Perform these connections when using the
optional amplifier.
38. Notes
• Change the initial setting of this unit (refer
to the operation manual). The subwoofer
output of this unit is monaural.
• When using a subwoofer of 70 W (2 Ω), be
sure to connect with Violet and Violet/black
leads of this unit. Do not connect anything
with Green and Green/black leads.