Inhaltsverzeichnis
Werbung
1.5 m
12. Note
Depending on the kind of vehicle,
20 cm
the function of 3* and 5* may be
1. USB cable
different. In this case, be sure to
Connect to sparately sold
connect 2* to 5* and 4* to 3*.
USB device.
7. This product
1*
8. Rear output or
3*
2*
subwoofer output
2. Antenna jack
5*
4*
9. Front output
3. Fuse (10A)
13. Connect leads of the
same color to each other.
14. Cap (1*)
Do not remove cap
if this terminal is
not in use.
15. Yellow (3*)
16. Yellow (2*)
Back-up (or
Connect to the constant
accessory)
12 V supply terminal.
17. Red (5*)
18. Red (4*)
Accessory
Connect to terminal controlled by
(or back-up)
ignition switch (12 V DC).
19. Orange/white
Connect to lighting switch terminal.
20. Black (chassis ground)
Connect to a clean, paint-free metal location.
21. ISO connector
Note
In some vehicles, the ISO connector
may be divided into two. In this case,
be sure to connect to both connectors.
4. AUX jack (3.5 φ)
Use a stereo mini plug cable
to connect with auxiliary
26.To Rear output or
device.
subwoofer output
5. Wired remote input
Hard-wired remote control
27.To front output
adaptor can be connected
(sold separately).
28. Connect with RCA cables
6. IP-BUS input (Blue)
(sold separately)
11.Multi-CD player
(sold separately)
10. IP-BUS cable
30. System remote control
22. Blue/white
Connect to system control terminal of the
power amp (max. 300 mA 12 V DC).
31. Front speaker
23. Blue/white (7*)
32. Left
Connect to auto-antenna relay control
terminal (max. 300 mA 12 V DC).
34.Rear speaker
24. Blue/white (6*)
or subwoofer
The pin position of the ISO connector will
differ depends on the type of vehicle.
Connect 6* and 7* when Pin 5 is an
35. Perform these connections when
antenna control type. In another type of
using the optional amplifier.
vehicle, never connect 6* and 7*.
36. Notes
25. Speaker leads
Front left
White:
• Change the initial setting of this unit (refer to the
White/black: Front left
operation manual). The subwoofer output of this unit is
Front right
Gray:
monaural.
Gray/black: Front right
• When using a subwoofer of 70 W (2 Ω), be sure to
Rear left or subwoofer
Green:
connect with Violet and Violet/black leads of this unit.
Green/black: Rear left or subwoofer
Do not connect anything with Green and Green/black
Rear right or subwoofer
Violet:
leads.
Violet/black: Rear right or subwoofer
Connecting the units
Note
• When this unit is installed in a vehicle without
ACC (accessory) position on the ignition switch,
red cable must be wired to the terminal that can
detect the operation of the ignition key. Otherwise,
29. Power amp
battery drain may result.
(sold separately)
29. Power amp
(sold separately)
ACC position
No ACC position
• Use this unit in other than the following
conditions could result in fire or malfunction.
— Vehicles with a 12-volt battery and negative
grounding.
— Speakers with 50 W (output value) and 4 ohm
to 8 ohm (impedance value).
• To prevent short-circuit, overheating or
malfunction, be sure to follow the directions
below.
— Disconnect the negative terminal of the
battery before installation.
— Secure the wiring with cable clamps or
31. Front speaker
adhesive tape. To protect the wiring, wrap
adhesive tape around them where they lie
against metal parts.
33. Right
— Place all cables away from moving parts, such
as gear shift and seat rails.
— Place all cables away from hot places, such as
near the heater outlet.
34.Rear speaker
— Do not pass the yellow cable through a hole
or subwoofer
into the engine compartment to connect to a
battery.
— Cover any disconnected cable connectors with
insulating tape.
— Do not shorten any cables.
— Never cut the insulation of the power cable of
this unit in order to share the power to other
equipment. Current capacity of the cable is
limited.
— Use a fuse of the rating prescribed.
— Never wire the speaker negative cable directly
to ground.
— Never band together multiple speaker's
negative cables.
English
Connecting the units
Connection Diagram
• Control signal is output through blue/white cable
when this unit is powered on. Connect it to an
1. USB cable
external power amp's system remote control or
Connect to separately sold USB device.
the vehicle's auto-antenna relay control terminal
2. Antenna jack
(max. 300 mA, 12 V DC). If the vehicle is equipped
with a glass antenna, connect it to the antenna
3. Fuse (10 A)
booster power supply terminal.
4. AUX jack (3.5 ø)
• Never connect blue/white cable to external power
Use a stereo mini plug cable to connect with
amp's power terminal. Also, never connect
auxiliary device.
it to the power terminal of the auto antenna.
5. Wired remote input
Otherwise, battery drain or malfunction may
Hard-wired remote control adaptor can be
result.
connected (sold separately).
• IP-BUS connectors are color-coded. Be sure to
6. IP-BUS input (Blue)
connect connectors of the same color.
• Black cable is ground. This cable and other
7. This product
product's ground cable (especially, high-current
8. Rear output or subwoofer output
products such as power amp) must be wired
9. Front output
separately. Otherwise, fire or malfunction may
10. IP-BUS cable
result if they are accidentally detached.
11. Multi-CD player (sold separately)
12. Note
Depending on the kind of vehicle, the function
of 3* and 5* may be different. In this case, be
sure to connect 2* to 5* and 4* to 3*.
13. Connect leads of the same color to
each other.
14. Cap (1*)
Do not remove cap if this terminal is not in use.
15. Yellow (3*)
Back-up (or accessory)
16. Yellow (2*)
Connect to the constant 12 V supply terminal.
17. Red (5*)
Accessory (or back-up)
18. Red (4*)
Connect to terminal controlled by ignition
switch (12 V DC).
19. Orange/white
Connect to lighting switch terminal.
20. Black (chassis ground)
Connect to a clean, paint-free metal location.
21. ISO connector
Note
In some vehicles, the ISO connector may
be divided into two. In this case, be sure to
connect to both connectors.
English
22. Blue/white
Connect to system control terminal of the
power amp (max. 300 mA 12 V DC).
23. Blue/white (7*)
Connect to auto-antenna relay control terminal
(max. 300 mA 12 V DC).
24. Blue/white (6*)
The pin position of the ISO connector will differ
depends on the type of vehicle. Connect 6*
and 7* when Pin 5 is an antenna control type.
In another type of vehicle, never connect 6*
and 7*.
25. Speaker leads
White: Front left
White/black: Front left
Gray: Front right
Gray/black: Front right
Green: Rear left or subwoofer
Green/black: Rear left or subwoofer
Violet: Rear right or subwoofer
Violet/black: Rear right or subwoofer
26. To rear output or subwoofer output
27. To front output
28. Connect with RCA cables (sold separately)
29. Power amp (sold separately)
30. System remote control
31. Front speaker
32. Left
33. Right
34. Rear speaker or subwoofer
35. Perform these connections when using the
optional amplifier.
36. Notes
• Change the initial setting of this unit (refer
to the operation manual). The subwoofer
output of this unit is monaural.
• When using a subwoofer of 70 W (2 Ω), be
sure to connect with Violet and Violet/black
leads of this unit. Do not connect anything
with Green and Green/black leads.
Werbung
Inhaltsverzeichnis
