Inhaltsverzeichnis
Werbung
2. Microphone input
8. Notes
1. This product
• Change the initial setting of this unit (refer to the
operation manual). The subwoofer output of this unit is
monaural.
7. Antenna
• When using a subwoofer of 70 W (2 Ω), be sure to
jack
connect with Violet and Violet/black leads of this unit.
Do not connect anything with Green and Green/black
6. Fuse (10 A)
leads.
9. Note
10. Speaker leads
Depending on the kind of vehicle,
the function of 2* and 4* may be
White:
Front left
different. In this case, be sure to
White/black: Front left
connect 1* to 4* and 3* to 2*.
Gray:
Front right
Gray/black: Front right
2*
1*
Green:
Rear left or subwoofer
Green/black: Rear left or subwoofer
Violet:
Rear right or subwoofer
Violet/black: Rear right or subwoofer
4*
3*
11. Connect leads of the
same color to each other.
12. Yellow (2*)
13. Yellow (1*)
Back-up (or
Connect to the constant
accessory)
12 V supply terminal.
14. Red (4*)
15. Red (3*)
Accessory
Connect to terminal controlled by
(or back-up)
ignition switch (12 V DC).
16. Black (chassis ground)
Connect to a clean, paint-free metal location.
17. ISO connector
Note
In some vehicles, the ISO connector may be
divided into two. In this case, be sure to
connect to both connectors.
21. Microphone
3. Rear output or
22. To rear output or
subwoofer output
subwoofer output
23. To front output
4. Front output
24. Power amp
5. Wired remote input
(sold separately)
Hard-wired remote
control adaptor can
be connected (sold
25. Connect with RCA cables
separately).
(sold separately)
26. System remote control
18. Blue/white
Connect to system control
27. Front speaker
27. Front speaker
terminal of the power amp (max.
300 mA 12 V DC).
19. Blue/white (6*)
Connect to auto-antenna relay
28. Rear speaker
28. Rear speaker
control terminal (max. 300 mA
or subwoofer
or subwoofer
12 V DC).
20. Blue/white (5*)
29. Perform these connections when
using the optional amplifier.
The pin position of the ISO
connector will differ depending
on the type of vehicle. Connect
5* and 6* when Pin 5 is an
antenna control type. In another
type of vehicle, never connect
5* and 6*.
Connecting the units
Note
• When this unit is installed in a vehicle without
ACC (accessory) position on the ignition switch,
red cable must be wired to the terminal that can
detect the operation of the ignition key. Otherwise,
battery drain may result.
24. Power amp
(sold separately)
ACC position
No ACC position
• Use this unit in other than the following
conditions could result in fire or malfunction.
— Vehicles with a 12-volt battery and negative
grounding.
— Speakers with 50 W (output value) and 4 ohm
to 8 ohm (impedance value).
• To prevent short-circuit, overheating or
malfunction, be sure to follow the directions
below.
— Disconnect the negative terminal of the
battery before installation.
— Secure the wiring with cable clamps or
adhesive tape. To protect the wiring, wrap
adhesive tape around them where they lie
against metal parts.
— Place all cables away from moving parts, such
as gear shift and seat rails.
— Place all cables away from hot places, such as
near the heater outlet.
— Do not pass the yellow cable through a hole
into the engine compartment to connect to a
battery.
— Cover any disconnected cable connectors with
insulating tape.
— Do not shorten any cables.
— Never cut the insulation of the power cable of
this unit in order to share the power to other
equipment. Current capacity of the cable is
limited.
— Use a fuse of the rating prescribed.
— Never wire the speaker negative cable directly
to ground.
— Never band together multiple speaker's
negative cables.
English
Connecting the units
Connection Diagram
• Control signal is output through blue/white cable
when this unit is powered on. Connect it to an
1. This product
external power amp's system remote control or
2. Microphone input
the vehicle's auto-antenna relay control terminal
(max. 300 mA, 12 V DC). If the vehicle is equipped
3. Rear output or subwoofer output
with a glass antenna, connect it to the antenna
4. Front output
booster power supply terminal.
5. Wired remote input
• Never connect blue/white cable to external power
Hard-wired remote control adaptor can be
amp's power terminal. Also, never connect
connected (sold separately).
it to the power terminal of the auto antenna.
6. Fuse (10 A)
Otherwise, battery drain or malfunction may
7. Antenna jack
result.
8. Notes
• Black cable is ground. This cable and other
product's ground cable (especially, high-current
• Change the initial setting of this unit (refer
products such as power amp) must be wired
to the operation manual). The subwoofer
separately. Otherwise, fire or malfunction may
output of this unit is monaural.
result if they are accidentally detached.
• When using a subwoofer of 70 W (2 Ω), be
sure to connect with Violet and Violet/black
leads of this unit. Do not connect anything
with Green and Green/black leads.
9. Note
Depending on the kind of vehicle, the function
of 2* and 4* may be different. In this case, be
sure to connect 1* to 4* and 3* to 2*.
10. Speaker leads
White: Front left +
White/black: Front left *
Gray: Front right +
Gray/black: Front right *
Green: Rear left + or subwoofer +
Green/black: Rear left * or subwoofer *
Violet: Rear right + or subwoofer +
Violet/black: Rear right * or subwoofer *
11. Connect leads of the same color to each other.
12. Yellow (2*)
Back-up (or accessory)
13. Yellow (1*)
Connect to the constant 12 V supply terminal.
14. Red (4*)
Accessory (or back-up)
15. Red (3*)
Connect to terminal controlled by ignition
switch (12 V DC).
16. Black (chassis ground)
Connect to a clean, paint-free metal location.
17. ISO connector
Note
In some vehicles, the ISO connector may
be divided into two. In this case, be sure to
connect to both connectors.
English
18. Blue/white
Connect to system control terminal of the
power amp (max. 300 mA 12 V DC).
19. Blue/white (6*)
Connect to auto-antenna relay control terminal
(max. 300 mA 12 V DC).
20. Blue/white (5*)
The pin position of the ISO connector will differ
depending on the type of vehicle. Connect 5*
and 6* when Pin 5 is an antenna control type.
In another type of vehicle, never connect 5*
and 6*.
21. Microphone
22. To rear output or subwoofer output
23. To front output
24. Power amp (sold separately)
25. Connect with RCA cables (sold separately)
26. System remote control
27. Front speaker
28. Rear speaker or subwoofer
29. Perform these connections when using the
optional amplifier.
Werbung
Inhaltsverzeichnis
