Werbung
9. Notes
1. This product
• Change the initial setting of this unit (refer to the
operation manual). The subwoofer output of this unit is
monaural (DEH-3200UB).
8. Antenna
• When using a subwoofer of 70 W (2 Ω), be sure to
jack
connect with Violet and Violet/black leads of this unit.
Do not connect anything with Green and Green/black
7. Fuse (10 A)
leads.
10. Note
11. Speaker leads
Depending on the kind of vehicle,
White:
Front left
the function of 2* and 4* may be
different. In this case, be sure to
White/black: Front left
connect 1* to 4* and 3* to 2*.
Gray:
Front right
Gray/black: Front right
2*
1*
Green:
Rear left
or subwoofer
Green/black: Rear left
or subwoofer
Violet:
Rear right
or subwoofer
Violet/black: Rear right
or subwoofer
4*
3*
12. Connect leads of the
same color to each other.
13. Yellow (2*)
14. Yellow (1*)
Back-up (or
Connect to the constant
accessory)
12 V supply terminal.
15. Red (4*)
16. Red (3*)
Accessory
Connect to terminal controlled by
(or back-up)
ignition switch (12 V DC).
17. Black (chassis ground)
Connect to a clean, paint-free metal location.
18. ISO connector
19. Yellow/black
Note
If you use an equipment with Mute
function, wire this lead to the Audio Mute
In some vehicles, the ISO connector may be
lead on that equipment. If not, keep the
divided into two. In this case, be sure to
connect to both connectors.
Audio Mute lead free of any connections.
23. For DEH-4200SD
24. To subwoofer output
2. Rear output or subwoofer output
(DEH-3200UB)
3. Rear output (DEH-4200SD)
25. To rear output
4. Front output (DEH-4200SD)
5. Subwoofer output
(DEH-4200SD)
26. To front output
6. Wired remote input
Hard-wired remote
control adaptor can
be connected (sold
separately).
28. Connect with RCA cables
(sold separately)
29. System remote control
20. Blue/white
Connect to system control
30. Front speaker
terminal of the power amp (max.
300 mA 12 V DC).
21. Blue/white (6*)
Connect to auto-antenna relay
31. Rear speaker
control terminal (max. 300 mA
12 V DC).
22. Blue/white (5*)
32. Subwoofer
The pin position of the ISO
connector will differ depending
33. Perform these connections when
on the type of vehicle. Connect
using the optional amplifier.
34. For DEH-3200UB
5* and 6* when Pin 5 is an
antenna control type. In another
type of vehicle, never connect
5* and 6*.
35. To rear output or
subwoofer output
37. Connect with RCA
cable (sold separately)
29. System remote control
36. Rear speaker
or subwoofer
Connecting the units
Note
• When this unit is installed in a vehicle without
ACC (accessory) position on the ignition switch,
red cable must be wired to the terminal that can
detect the operation of the ignition key. Otherwise,
27. Power amp
battery drain may result.
(sold separately)
27. Power amp
(sold separately)
27. Power amp
(sold separately)
ACC position
No ACC position
• Use this unit in other than the following
conditions could result in fire or malfunction.
— Vehicles with a 12-volt battery and negative
grounding.
— Speakers with 50 W (output value) and 4 ohm
to 8 ohm (impedance value).
• To prevent short-circuit, overheating or
malfunction, be sure to follow the directions
below.
— Disconnect the negative terminal of the
battery before installation.
30. Front speaker
— Secure the wiring with cable clamps or
adhesive tape. To protect the wiring, wrap
adhesive tape around them where they lie
against metal parts.
31. Rear speaker
— Place all cables away from moving parts, such
as gear shift and seat rails.
— Place all cables away from hot places, such as
near the heater outlet.
— Do not pass the yellow cable through a hole
32. Subwoofer
into the engine compartment to connect to a
battery.
— Cover any disconnected cable connectors with
insulating tape.
— Do not shorten any cables.
— Never cut the insulation of the power cable of
27. Power amp
this unit in order to share the power to other
(sold separately)
equipment. Current capacity of the cable is
limited.
— Use a fuse of the rating prescribed.
— Never wire the speaker negative cable directly
to ground.
— Never band together multiple speaker's
negative cables.
36. Rear speaker
or subwoofer
English
Connecting the units
Connection Diagram
• Control signal is output through blue/white cable
when this unit is powered on. Connect it to an
1. This product
external power amp's system remote control or
2. Rear output or subwoofer output
the vehicle's auto-antenna relay control terminal
(max. 300 mA, 12 V DC). If the vehicle is equipped
(DEH-3200UB)
with a glass antenna, connect it to the antenna
3. Rear output (DEH-4200SD)
booster power supply terminal.
4. Front output (DEH-4200SD)
• Never connect blue/white cable to external power
5. Subwoofer output (DEH-4200SD)
amp's power terminal. Also, never connect
6. Wired remote input
it to the power terminal of the auto antenna.
Hard-wired remote control adaptor can be
Otherwise, battery drain or malfunction may
connected (sold separately).
result.
• Black cable is ground. This cable and other
7. Fuse (10 A)
product's ground cable (especially, high-current
8. Antenna jack
products such as power amp) must be wired
9. Notes
separately. Otherwise, fire or malfunction may
• Change the initial setting of this unit (refer
result if they are accidentally detached.
to the operation manual). The subwoofer
output of this unit is monaural
(DEH-3200UD).
• When using a subwoofer of 70 W (2 Ω), be
sure to connect with Violet and Violet/black
leads of this unit. Do not connect anything
with Green and Green/black leads.
10. Note
Depending on the kind of vehicle, the function
of 2* and 4* may be different. In this case, be
sure to connect 1* to 4* and 3* to 2*.
11. Speaker leads
White: Front left
White/black: Front left
Gray: Front right
Gray/black: Front right
Green: Rear left
or subwoofer
Green/black: Rear left
Violet: Rear right
Violet/black: Rear right
12. Connect leads of the same color to each other.
13. Yellow (2*)
Back-up (or accessory)
14. Yellow (1*)
Connect to the constant 12 V supply terminal.
15. Red (4*)
Accessory (or back-up)
16. Red (3*)
Connect to terminal controlled by ignition
switch (12 V DC).
17. Black (chassis ground)
Connect to a clean, paint-free metal location.
18. ISO connector
Note
In some vehicles, the ISO connector may
be divided into two. In this case, be sure to
connect to both connectors.
English
19. Yellow/black
If you use an equipment with Mute function,
wire this lead to the Audio Mute lead on that
equipment. If not, keep the Audio Mute lead
free of any connections.
20. Blue/white
Connect to system control terminal of the
power amp (max. 300 mA 12 V DC).
21. Blue/white (6*)
Connect to auto-antenna relay control terminal
(max. 300 mA 12 V DC).
22. Blue/white (5*)
The pin position of the ISO connector will differ
depending on the type of vehicle. Connect 5*
and 6* when Pin 5 is an antenna control type.
In another type of vehicle, never connect 5*
and 6*.
23. For DEH-4200SD
24. To subwoofer output
25. To rear output
26. To front output
27. Power amp (sold separately)
28. Connect with RCA cables (sold separately)
29. System remote control
30. Front speaker
31. Rear speaker
32. Subwoofer
33. Perform these connections when using the
optional amplifier.
34. For DEH-3200UB
or subwoofer
35. To rear output or subwoofer output
or subwoofer
36. Rear speaker or subwoofer
or subwoofer
37. Connect with RCA cable (sold separately)
Werbung
