Conrad XQ-150 Bedienungsanleitung Seite 24

Table des matières
Introduction ...............................................................................................................49
Utilisation conforme ..................................................................................................49
Table des matières ....................................................................................................50
Consignes de sécurité ..............................................................................................51
Description des fonctions .........................................................................................52
Mise en service .........................................................................................................52
Montage mécanique ............................................................................................52
Branchement électrique.......................................................................................55
Branchement des entrées de l'amplificateur .......................................................58
Branchement des sorties de l'amplificateur ........................................................59
Utilisation .............................................................................................................63
Manipulation..............................................................................................................67
Entretien ....................................................................................................................67
Elimination.................................................................................................................68
Elimination de défaillances........................................................................................68
Caractéristiques techniques .....................................................................................70
Désignation des pièce constitutives
(Figure voir page repliée en annexe)
1. Commutateur modes de fonctionnement 21. Touche SEL
CH 3,4
2. Entrée MAIN-IN
3. Entrée auxiliaire AUX-IN
4. Sortie SUBWOOFER LINE-OUT
5. DEL PROTECT
6. DEL POWER
7. Touche RESET
8. Branchement REMOTE CONTROLLER
9. Fusibles FUSE
10. Raccordement alimentation courant B+
11. Raccordement alimentation courant REM 31. Affichage FAD
12. Raccordement alimentation courant GND 32. Indication pour sensibilité de l'affichage
13. Raccordement haut-parleur CH 3+
14. Raccordement haut-parleur CH 3-
15. Raccordement haut-parleur CH 4+
16. Raccordement haut-parleur CH 4-
17. Raccordement haut-parleur CH 1+
18. Raccordement haut-parleur CH 1-
19. Raccordement haut-parleur CH 2+
20. Raccordement haut-parleur CH 2-
50
Page
22. Touche STO
23. Touche DISP
24. Touche UP/DOWN
25. Touche RCL
26. Touche SRC
27. Touche SUB
28. Touches équilibreur
29. Touches mémorisation
30. Affichage VOL
33. Affichage pour subwoofer
34. Affichages pour sélection de l'entrée
35. Affichage pour mémoire
36. Affichage intensité sonore, position fader,
intensité sonore subwoofer,
fréquence de séparation subwoofer
37. Affichage pour les presets
38. Affichage du spectre
One channel • Check the connections to MAIN-IN (2) or AUX-IN (3) input
does not function • Check the loudspeaker output and loudspeaker connec-
tions
• The car radio balance control is not in its centre position
Interference • Poor earthing cable connection to chassis, remove possible
noise occurs rust or paint
• from the contact surfaces
• The earthing points of the car radio and of the amplifier are
not at the same potential; try various earthing points
• The amplifier cables are too close to the vehicle ignition
system cables
• The ignition system is not suppressed
• The amplifier input cables are too close to the voltage sup-
ply cables
The equipment • Poor earthing cable contact to chassis; cable connection
switches on and point or battery terminal corroded
off during operation • Voltage at current supply connection B+ (10) too low;
cable connection point or battery terminal corroded;
battery too weak
• Remote cable has loose contact; current supply connection
REM (11) has loose contact or is corroded
Reproduction • A loudspeaker is connected in reverse
occurs with no • The car radio bass control is at minimum
bass tones • The equaliser is incorrectly set
Reproduction • The operating mode switch CH 3,4 (1) is incorrectly set
occurs with no • The equaliser is incorrectly set
mid- to high
tones
Repairs other than described above are to be carried out exclusi-
vely by an authorised specialist.
47