Watch.mode; Watch.times; Watch.default.time; Countdown.timer.status - Talis IQ-1201 Benutzerhandbuch

WATCH TIMES
Main Time is the current Time at your home location and is normally selected as the Watch Default Time (Fig. 7A).
Alternate Time, which is set by Hour Differential, is the Time at a remote location (away). Upon arrival at the location, Alternate
Time, identified by the AWAY icon (Fig. 7B a), can be selected to be the Watch Default Time.
Dual Time, identified by the AWAY icon (Fig. 7C a), is an additional time which is usually Alternate Time but can be Main Time
depending on which one is not selected to be the Watch Default.
• When an Alternate Time is set, and Show Dual Time is set for YES, both Times will be displayed on the Watch Default Time
screen (Fig. 7C).
• When an Alternate Time is set, and Show Dual Time is set for NO, Dual Time will be displayed on the Watch ALT screen
(Fig. 8) accessed by pressing the M button.
Watch Mode selections, which can be accessed by pressing the M button while viewing the Default Time screen, include:
Watch ALT (additional data) >> Countdown Timer >> Chronograph >> Daily Alarm.
• M (< 2 sec) - to step forward through the selections.
• A (2 sec) - to step back through the selections.
WATCH DEFAULT TIME, information includes (Fig. 7A - 7D):
> Graphic MON (or TUE, WED, THU, FRI, SAT, SUN); or Dual Time (hr:min) with icon, if an Alternate Time has been set and
Show Dual is set for YES.
> Daily Alarm icon (clock) if it is set On (Fig. 7a).
> Time of Day (hr:min:sec) with AM (or PM) icon if 12 Hour Format, no icon if 24 Hour; and AWAY icon (Fig. 7B a) if
Alternate Time is selected to be the Default Time.
> Nitrogen Bar Graph, if any after NORM or FREE dives.
> Battery icon, if a Low Battery condition exists.
• M (< 2 sec) - to access the Watch ALT screen, then step forward through Watch mode selections.
• M (2 sec) - to access Dive Computer Surface Modes (NORM, GAUG, or FREE).
• A (< 2 sec) - to access NORM/GAUG Log and History.
• A (2 sec) - to access the Show Dual Time selection, then step back through other Watch Set selections*.
• S (< 2 sec) - to silence and acknowledge the Daily Alarm.
• A + S buttons (2 sec) - to access Set Date Format then allow stepping forward through Watch Set selections*.
• L (press) - to activate the Backlight.
WATCH ALT DATA, information includes (Fig. 8A, 8B):
> Dual (away) Time (hr:min) with icon if an Alternate Time has been set and Show Dual is set for NO; or graphic MON (or
TUE, WED, THU, FRI, SAT, SUN) if Show Dual is set for YES (displayed on the Default Time screen).
> Temperature with °F (or °C).
> Date (Month.Day or Day.Month).
> Altitude graphic (EL2 to EL7), if above 3000 feet (915 meters), blank if below.
• M (< 2 sec) - to step forward to CDT Status.
• A (< 2 sec) - to step back to Watch Default Time.
• Revert to Watch Default Time after 5 seconds if M or A is not pressed.
• L (press) - to activate the Backlight.
WATCH CDT (COUNTDOWN TIMER) STATUS
Upon accessing a dive computer mode, Watch CDT operation will be terminated and the time reset to the previous setting.
The CDT will run in the background until it counts down to 0:00, or it is set OFF, or Dive Computer Mode is accessed or a Dive is
started in which case the countdown will terminate and revert to OFF with the hr:min time previously set.
When a set CDT reaches 0:00, the Audible will sound during which time the graphic CDT will flash on the Watch Main.
CDT Status, information includes (Fig. 9A):
> Graphic CDT.
> Graphic OFF (or ON) flashing. If OFF, 0:00 or the hr:min previously set. If ON, the hr:min countdown remaining.
• S (< 2 sec) - to toggle between OFF and ON. A toggle to ON will start the countdown if set and OFF.
• A + S (2 sec) - to access Set CDT.
• A (2 sec) - to step back to the Watch ALT screen.
• M (2 sec) - to revert to the Watch Default Time screen.
• Revert to Watch Default Time after 2 minutes if no button is pressed.
• L (press) - to activate the Backlight.
©2002 Design, 2014
9
TALIS
OWNER'S MANUAL
a
Fig. 7A - DEFAULT TIME
(Main selected, at home)
a
Fig. 7B - DEFAULT TIME
(away, Alternate selected)
a
Fig. 7C - DEFAULT TIME
(Main with Dual)
Fig. 7D - DEFAULT TIME
(away, Alternate with Dual)
Fig. 8A - WATCH ALT
(Show Dual set for NO)
Fig. 8B - WATCH ALT
(Show Dual set for YES)
Fig. 9A - WATCH CDT
STATUS
Doc. No. 12-5355-r01 (1/20/14)