Free.dive.mode; Free.countdown.timer.(Cdt) - Talis IQ-1201 Benutzerhandbuch

FREE DIVE MODE
When Free Dive Mode is selected, Nitrogen loading is calculated based on a default FO2 of AIR and the amount remaining dur-
ing 24 hours is carried over between FREE and NORM operating modes.
• M (2 sec), while viewing the GAUG Surface Main screen - to access FREE Mode.
• M (< 2 sec), while the graphic FRE is flashing, will select FREE as the operating dive mode. The graphic FRE becomes solid
and FREE Mode is selected.
FREE Surface Main, information includes (Fig. 86):
> Graphic FRE.
> Graphic tot with Total number of repetitive Free dives conducted (0 if none yet) in that series with # icon.
> Surface Interval after the most recent dive (min:sec to 59:59, then hr:min) with clock/wave icon (above, next to FRE).
> Battery icon if a Low Battery condition exists.
• A (< 2 sec) - to access ALT 1.
• A (2 sec) - to access FREE CDT Status.
• A + S (2 sec) to access the Set Alarms.
• M (< 2 sec) - to access Watch Default Time.
• L (press) - to activate the Backlight.
FREE Surface ALT 1, information includes (Fig. 87):
> Surface Interval prior to last dive (min:sec) with clock/wave icon.
> Graphic LASt.
> EDT (min:sec) of last dive with wave/clock icon.
> Max Depth of last dive with MAX and FT (or M) icons.
• A (< 2 sec) - to access ALT 2.
• Revert to Main after 5 seconds if A is not pressed.
• L (press) - to activate the Backlight.
FREE Surface ALT 2, information includes (Fig. 88):
> Temperature with °F (or °C).
> Time of Day (hr:min) with Time (clock ) icon, and AWAY icon if Alternate is selected as the Watch Default Time.
• A (< 2 sec) - to revert to the Main, or after 5 seconds if A is not pressed.
• L (press) - to activate the Backlight.
FREE COUNTDOWN TIMER (CDT)
While viewing the CDT Status screen, the Timer can be started, stopped, and set.
The Status screen displays the graphics CDT and OFF (solid) with 0:00 if no time was previously set, ON if running with Count-
down Time (min:sec) remaining, or OFF flashing and the previously Countdown Time set.
Once set ON, a Countdown will run in the background until it counts down to 0:00, or it is set OFF.
When a set Countdown Time reaches 0:00, the Audible will sound during which the graphic CDT will flash on the FREE Surface
Main (Fig. 89).
Once the CDT has been Set and Started (by selecting ON), it will continue to run in the background while on the surface until
turned OFF (stopped) or the Time reaches 0:00 at which time the Alarm will strike, the graphic CDT will be displayed, and the
Timer will revert to OFF.
> Upon descending to 5 FT/1.5 M (i.e., entry into Free Dive mode), CDT operation will continue, if in progress.
> During a dive, the CDT can be turned OFF (stopped) and ON (started), but not Set.
CDT Status, information includes (Fig. 90):
> Graphic CDT.
> Graphic OFF (or ON) flashing. If OFF, 0:00 or the min:sec previously set. If ON, the min:sec countdown remaining.
• S (< 2 sec) - to toggle between OFF and ON. A toggle to ON will start the countdown if set and OFF.
• A + S (2 sec) - to access Set CDT.
• A (2 sec) - to step back to the FREE Surface Main screen.
• M (2 sec) - to revert to the FREE Surface Main screen
• Revert to FREE Surface Main after 2 minutes if no button is pressed.
• L (press) - to activate the Backlight.
©2002 Design, 2014
--------------------------------------------------------------------------------------------------------
39
TALIS
OWNER'S MANUAL
Fig. 86 - FREE SURF MAIN
Fig. 87 - FREE SURF ALT 1
Fig.88 - FREE SURF ALT 2
Fig. 89 - FREE SURF MAIN
(during CDT Alarm)
Fig. 90 - CDT STATUS
(Off, not set)
Doc. No. 12-5355-r01 (1/20/14)