Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
DIVE COMPUTER (DC) OPERATING MODES
The Talis features 3 DC Operating Modes -
• NORM >> for Normal Air or Nitrox dives using scuba.
• GAUG >> for scuba dives with no nitrogen/oxygen calculations.
• FREE >> for breath hold dives with no SCUBA.
SURFACE MODE
M (2 sec), while the Watch Default Time screen is displayed - to access the DC Surface Main screen.
If no other dive has been conducted within the past 24 hours, the NORM Surface Main will appear as the default display indicat-
ed by the graphic Nor (Fig. 23). If a GAUG or FREE dive has been conducted within the past 24 hours, the Surface Main screen
for that Operating Modewill be displayed.
• The GAUG and FREE Surface Main screens can be accessed by depressing M (2 sec) . Their graphics will flash indicating
that they can be selected as the Operating Dive Mode.
• To select a Mode for diving, press/release M (< 2 sec) while that graphic is flashing. When the graphic becomes solid, that
Mode is selected for the type of dives to be conducted.
• The Operating Mode selected (NORM, GAUG, or FREE) will remain on display for 2 hours until a dive is made or another
Operating Mode is selected.
At any time while operating in Surface Modes, the Talis will enter Dive Mode upon descent to 5 FT (1.5 M).
• During the 2 hour pre dive surface period, if other screens in the Watch Mode sequence are accessed, Surface Mode must
again be accessed prior to the first dive of a series (if Wet Activation is set OFF).
• When Wet Activation is set ON, the Wet Contacts will activate the selected Dive Mode regardless of what Mode the Talis is
operating in at the time of the descent.
The Talis will enter Post Dive Surface Mode following a dive upon ascent to 2 FT (0.6 M). The Surface Interval Time colon will
flash during the first 10 minutes after a NORM or GAUG dive (Fig. 24), or 1 minute after a FREE dive.
During the first 10 minutes after a dive, the Surface Main screen for the operating mode remains on display. Watch Default Time
can be viewed for 5 seconds during that period by pressing M (< 2 sec).
When the 10 minute Surface Time has elapsed, the Watch Default Time screen will replace the DC Surface Main screen which
can then be accessed by M (2 sec).
NORM SURF MAIN, information provided includes (Fig. 25):
> Surface Interval Time (hr:min) with clock/wave icon.
> Graphic Nor.
> Tank 1 icon (default on surface); or 2 (the Gas in use during 10 minutes after a dive).
> Number of that dive with # icon, 0 if no dive has been made yet.
> Battery icon if a Low Battery condition exists.
> NiBG, if any after a NORM or FREE dive.
• A (2 sec) - to access NORM SURF ALT.
• A (< 2 sec) - to access Log Mode and History.
• A & S (2 sec) - to access Set Modes.
• M (2 sec) - to access GAUG and FREE Surface Mains.
• M (< 2 sec) - to access to Watch Default Time.
• S (< 2 sec) - to access Plan, Fly, and Dsat.
• L (press) - to activate the Backlight.
NORM SURF ALT, information includes (Fig. 26):
> % O2 saturation remaining after Nitrox dives with icons.
> Temperature with °F (or °C).
> Time of Day (hr:min) with Time (clock ) icon, and AWAY icon if Alternate is selected as the Watch Default Time.
> Altitude graphic (EL2 to EL7), if above 3000 feet (915 meters), blank if below.
• A (< 2 sec) - to revert to NORM Surface Main.
• Revert to NORM Surface Main after 5 seconds if A is not pressed..
• L (press) - to activate the Backlight.
©2002 Design, 2014
--------------------------------------------------------------------------------------------------------
--------------------------------------------------------------------------------------------------------
--------------------------------------------------------------------------------------------------------
16
TALIS
OWNER'S MANUAL
Fig. 23 - NORM SURF MAIN
Fig. 24 - GAUG SURF MAIN
(< 10 min after a dive)
Fig. 25 - NORM SURF MAIN
Fig. 26 - NORM SURF ALT
Doc. No. 12-5355-r01 (1/20/14)
Werbung
Kapitel
Inhaltsverzeichnis
