Problems And Remedies - Quick MILL 4100 Bedienungsanleitung

Mod. 04100
corrosive or abrasive detergents. Always use a damp
cloth or sponge or one soaked in alcohol.
10.1. Daily

Clean the outer body with a damp cloth or one
soaked in alcohol.

Clean the spout of the steam nozzle 8.

Clean the spray units and the seals under the casing
of the delivery units using the special brush
supplied.

Check and, if necessary, clean the drain pan.

Rinse the filters and the filter holder with hot water
and a cloth or sponge. Carefully remove any coffee
residues or deposits.
10.2. Periodic cleaning of the machine or after a period
of intense use.
In addition to daily cleaning, perform the following
operations:

Immerse the filters and the filter holder 13 in
boiling water for a few minutes to dissolve coffee
greases and oils, then use a cloth or a sponge to
remove them completely.

Clean the water reservoir 10 taking care to
reposition the rubber tube with the filter until it
touches the bottom of the reservoir (do not use a
dishwasher for this).
10.3. Extraordinary maintenance
The machine is supplied with a blind filter used to clean
the group and the solenoid valve. This operation must
be performed at least once a week to remove coffee
deposits in the circuit.

Remove the filter holder 13 from the group
12.

Remove the filter from the filter holder 13.

Insert the blind filter in the filter holder 13.

Attach the filter holder 13 to the group 12.

Start coffee delivery with button 2 for
approximately 15 seconds, then stop
delivery.

Repeat the operation described in point 6
for 10-15 times.

Remove the filter holder and the blind
filter.
During cleaning operations using the
blind filter, boiling water will be
discharged into the drain pan14. Pay
attention to possible splashing water which
could exit from the cup rest grille. The
procedure for cleaning the group may be
performed with the aid of a degreasing product,
specific for coffee machines. In this instance,
follow the instructions of use for the product to
be used.
11. DECOMMISSIONING
11.1. Temporary

Empty the water reservoir 10 and the spill basin.

Close all switches and remove the power plug from
the mains.

Perform the maintenance operations.

Store the machine in a dry environment, protected
from the elements and with limited access (avoid
leaving it in the reach of minors or unfit persons).
11.2. Definitive
Besides carrying out the operations necessary for a
temporary stop, do the following:

Cut or eliminate the power cable;

Pack the machine in cardboard or other packing
material and send it to authorised personnel for its
disposal or second-hand sale).

12. PROBLEMS AND REMEDIES

In the event the power cable is damaged,
contact an authorised service centre to have it
replaced.
The disposable materials used for processing or
maintenance, if non-biodegradable or are pollutants,
should be placed in separate containers and sent to
special waste disposal centres.
Inspections which can be performed by the user are to
be performed only after the electrical power supply has
been isolated.
A) The machine does not start:

Check that the plug is connected to the mains.

Check that there is power supply available and that
the residual current device is inserted and the main
switch is in the ON position.

Check the condition of the plug and the power
supply cable; if damaged have them replaced by
qualified personnel.
B) No coffee is delivered:

No water in the reservoir; refill and repeat the
operations in section 9.1 (Filling with water).

The level of water in the boiler was not restored
after the delivery of steam.
C) No hot water or steam delivery:

No water in the reservoir; refill with water.

The level of water in the boiler was not restored
after the delivery of steam. Nozzles or steam spout
clogged; clean the nozzles of the sprayer outlet of
the steam spout.
E) Irregular delivery of coffee:

Clean the filter in the filter holder.

The coffee grounds are too fine or too coarse.
For any other type of irregularity or problem
which has not been specified, unplug the
power supply cable, avoid performing any
direct repairs or inspections and contact a qualified
technical service centre.
Rev.00