Installing Batteries In The Remote Controls; Using The Remote Controls - Yamaha RX-797 Bedienungsanleitung

CONTROLS AND FUNCTIONS

Installing batteries in the remote controls

■ Notes on batteries
• Change all of the batteries if the operation range of the remote controls decreases.
• Use AA, R6, UM-3 batteries for the remote control and AAA, R03, UM-4 batteries for the Zone 2 remote control.
• Make sure that the polarities are correct. See the illustration inside the battery compartment of each remote control.
• Remove the batteries if the remote controls are not used for an extended period of time.
• Do not use old batteries together with new ones.
• Do not use different types of batteries (such as alkaline and manganese batteries) together. Read the packaging carefully as these
different types of batteries may have the same shape and color.
• We strongly recommend using alkaline batteries.
• If the batteries have leaked, dispose of them immediately. Avoid touching the leaked material or letting it come into contact with
clothing, etc. Clean the battery compartment thoroughly before installing new batteries.
• Do not throw away batteries with general house waste; dispose of them correctly in accordance with your local regulations.
Remote control
1
1
Open the battery compartment cover.
2
Insert the supplied batteries in each remote
control according to the polarity markings (+
and –) on the inside of the battery
compartment.

Using the remote controls

The remote controls transmit a directional infrared beam.
Be sure to aim the remote controls directly at the remote control sensor on the front panel of this unit or on the infrared
signal receiver in Zone 2 during operation.
ZONE 2 ON/OFF
ZONE CONTROL
MASTER SPEAKERS
A B A/B/C/D/E 1 2 3 4
ON OFF
INPUT REC OUT BASS TREBLE
MAIN ZONE
SOURCE 0 0
PHONES MD/TAPE CD 1 1 1 1
VCR TUNER 2 2 2 2
ON/OFF DTV/CBL PHONO 3 3 3 3
DVD 4 4 4 4
– 5 5 + – 5 5 +
30 30
POWER POWER STANDBY POWER
TV AV
CD MD/TAPE TUNER
DVD DTV/CBL VCR PHONO
REC CODE SET SPEAKERS
A
DISC SKIP
B
FREQ/TEXT EON
SLEEP
MODE PTY SEEK START
TV VOL TV CH VOLUME
TV MUTE TV INPUT
MUTE
1 2 3 4
5 6 7 8
9 0 10 ENT.
TITLE MENU
BAND
ENTER
A/B/C/D/E A/B/C/D/E
RETURN DISPLAY
PRESET/CH
10
2
3
FM/AM l TUNING h
PURE DIRECT CD DIRECT AMP
EDIT MEMORY TUNING MODE
MAN'L/AUTO FM AUTO/MAN'L
5 6 7 8 VOLUME
BALANCE LOUDNESS
0 FLAT
1 1 1
–30dB
2 2 2 10
3 3 3 9
4 4 4 8
L 5 5 R 5 7
6
Approximately 6 m (19.7 ft)
Zone 2 remote control
1
3
Close the cover back.
■ Handling the remote controls
• The area between the remote controls and this unit (or the
infrared signal receiver in Zone 2) must be clear of large
obstacles.
• Do not spill water or other liquids on the remote controls.
• Do not drop the remote controls.
• Do not leave or store the remote controls in the following types
of conditions:
– places of high humidity, such as near a bath
– places of high temperature, such as near a heater or a stove
– places of extremely low temperatures
– dusty places
• Do not expose the remote control sensor to strong lighting, in
particular, an inverter type fluorescent lamp; otherwise, the
remote controls may not work properly. If necessary, position
this unit away from direct lighting.
3
2